Power System Stability Enhancement Using FLC and MPC for STATCOM

Dr.A.Rajalingam et al. Int. Journal of Engineering Research and Applications www.ijera.com
ISSN: 2248-9622, Vol. 6, Issue 1, (Part - 5) January 2016, pp.107-113
www.ijera.com 107|P a g e
Power System Stability Enhancement Using FLC and MPC for
STATCOM
Dr.A.Rajalingam1
, Dr.M.Ramkumar Prabhu2
, & K.Venkateswara Rao3
1&2
Professor, 3
Asst. Professor Department of Electronics & Communication Engineering
1
Shinas College of Technology, Sultanate of Oman.
2
Dhaanish Ahmed College of Engineering, Chennai, India.
3
RVS Padmavathy College of Engineering & Technology
Abstract
In modern power system, Static Compensator (STATCOM) is used to alleviate the transient stability problem
and damping power system oscillations. In this paper different STATCOM control scheme using fuzzy logic
controller (FLC) and model predictive controller (MPC) for the Single Machine Infinite Bus (SMIB) system in
improving transient stability is simulated using MATLAB/ Simulink in power systems block set. PI, FLC and
MPC signals are used to control and exchange the required reactive power among the STATCOM and the power
grid. A load disturbance is simulated and the behavior of the system for voltage fluctuations has been studied.
Simulation results using Proportional-Integral (PI) controller, Fuzzy Logic Controller (FLC) and Model
Predictive Controller (MPC) have been compared. The effectiveness of the different controllers in damping
oscillations and improving power system stability has been discussed.
Keyword- Static Synchronous Compensator (STATCOM), PI controller, fuzzy logic controller (FLC), Model
Predictive Controller (MPC), Flexible AC Transmission System (FACTS).
I. INTRODUCTION
Flexible AC Transmission Systems (FACTS)
employs power electronics device to control the real
and reactive power in modern power system for the
better utilization of the existing network [1]. The
beginning of FACTS as an entire network control
attitude was introduced in the year 1988 and its
effectiveness is now widely recognized by the power
system researchers and engineers [2]. As the FACTS
controllers are fast operating they are mainly utilized
in improving steady state and transient stabilities of a
modern power system. This enhances the maximum
utilization of the existing network without further
expansion and operating the network close to the
thermal loadable limit [3]. The conventional shunt
compensators have been replaced by Static VAR
compensator (SVC) for the power system voltage
stability improvement [4].
They are used to damp out power swings thereby
reducing the transmission loss by proper reactive
power control and enhances the transient stability.
Fast acting Static synchronous compensator
(STATCOM) is extensively used as dynamic shunt
compensator for reactive power control in the
transmission network [5]. VSC based STATCOM
have been developed to control power system
dynamics during fault condition. It has been reported
by many researches that STATCOM with modern
controller can be used to develop stability of system
of multi machine system and a single machine
infinite bus (SMIB) system [6]. Many advanced
control technologies have been proposed by the
researchers for STATCOM in improving stability of
power system stability.
In this work, the effect of STATCOM in a SMIB
system is studied under the MATLAB –SIMULINK
power system tool bar. The variations in both real
and reactive power exchange with STATCOM and
without STATCOM have been studied. A
proportional –Integral controller have been developed
and the performance of the controller with
STATCOM in the SMIB system has been analyzed
for a load disturbance. Then the PI controller is
replace by a more robust Fuzzy logic controller
(FLC) and Model Predictive controller (MPC) in
MATLAB-SIMULINK environment and the
efficiency of the different controllers have been
studied.
II. DYNAMIC MODEL OF SMIB
WITH STATCOM
In modern Power Systems the transient stability
problems are associated with the dynamics of
synchronous generators, field excitation systems and
the associated turbine governors. The active model of
SMIB with STATCOM controller is displayed in
figure 1. The active losses of transformer and
transmission line, inverter switching losses and
power losses in capacitor are neglected in this model.
The three important stages of STATCOM are power
stage of converter, the control system and the passive
components. The STATCOM dynamic model
RESEARCH ARTICLE OPEN ACCESS

comprises of a generating voltage source (UT) after a
leakage reactance of transformer (XS) and
a dc capacitor (UDC) is coupled with a voltage source
converter (VSC). The STATCOM V-I characteristics
are displayed in fig 2
Fig1. Dynamic model of SMIB system with
STATCOM
Fig2. V-I characteristics of STATCOM
Both capacitive and inductive compensation is
provided by the controller and is capable of
controlling the output current value over the rated
maximum inductive and capacitive range in the ac
system voltage.The capacitor voltage UDC is
effectively controlled by monitoring difference in
phase angle between the voltage source converter
voltage Uc and the line voltage of AC system. If the
firing angle is advanced then the dc voltage is
decreased and reactive power flow into the
STATCOM. On the other hand if the firing angle is
delayed then increase in the dc voltage occurs and the
STATCOM will supply reactive power into ac
system. Hence by the control of the firing angle of
the VSC the STATCOM is operated in absorbing or
pumping reactive power. By controlling the reactive
power the proper voltage regulation can be achieved
and the system stability can be enhanced greatly [7],
[8] & [9].
The equivalent circuit of STATCOM is
presented in figure.3
The parameter Ls and Rs represents the
STATCOM transformer inductance and resistance.
The basic equation of the circuit in vector form is
given by
iabc = iabc + (Eabc – Vabc) (1)
The STATCOM output equation is specified
byEa=KUdc cos(ωt+α) (2)
where the UDC is the capacitor voltage, K is the
modulation index α represents the voltage phase
angle.
An equation for voltage across the capacitor is given
by
C +GUdc = mk[sin(α + θ) ID + cos (α + θ) I Q] (3)
In this equation G represents the losses associated in
the capacitor while the angle α and m are the control
parameters of the VSC [10] & [11]. In this work
IGBT based STATCOM is used for the study and the
parameter m is kept constant and the angle α is the
control parameter in controlling the reactive power.
III. SIMULATION OF SIMPLE POWER
SYSTEM
A. A model Power System simulation without
using STATCOM
To study the transient stability phenomenon a
simplest power system is analyzed by the utilization
of SimPower System toolbox presented in the
MATLAB/Simulink software environment. Fig.1
represents single line diagram of SMIB system which
comprises of a transmission line connecting an AC
power source at the sending end and a receiving side
connected to a RL load. This arrangement is first
studied without STATCOM using a generating
source with 230 kV voltage which simulates a
synchronous generator of 500MVA capacity with
terminal voltage 11kV, and its associated step up
transformer with 500MVA, 11/230kV rating. The
real power flow and reactive power flow in this
configuration and the associated sending end and
receiving end parameters have been observed. In
Simulink Power system blocks, the reactive and
active power blocks are available for measuring the
power flow both at the sending end and the receiving
end

Fig4. A simple power system – Simulink diagram
The RL load value is assumed to have a real
power value of 500 MW and reactive power of 100
MVAR. The length of the transmission line is
assumed to be 300Km. The readings of both sending
end power and receiving end power and voltage
values are observed, and it is tabulated in table 1
TABLE 1
Simple power system without STATCOM -
Simulation results
Under this loading condition, the real power at the
receiving end is lesser than the real power at sending
end and the reactive power at the receiving end is
also lesser than the reactive power at the sending end.
B. Simple Power System simulation with
STATCOM
In order to analyse the same SMIB system with
STATCOM controller SIMULINK model has been
developed with the controller located in the midpoint
of the transmission line. VSC based STATCOM
arrangement is implemented which has three arm
bridges IGBT coupled with shunt transformer and it
is connected in mid-point of transmission line. Here
the working principle of STATCOM is to inject the
reactive power into simplest power system when
system bus voltage is lesser than inverter output
voltage and from system bus reactive power is
absorbed when system bus voltage is greater than the
inverter output voltage. Fig 5 displays a Simulink
diagram of simplest power system with STATCOM
Fig5. A model power system with STATCOM–
Simulink diagram
TABLE 2
A model power system using STATCOM
C. Simple Power System simulation with
STATCOM controlled by PI controller
Fig.6 represents that PI controller is controlled
STATCOM device which is compensate the voltage
control and reactive power at the receiving end. First
to simulate the system with STATCOM is controlled
by PI controller and read the response when load
disturbance will occur in simulated system
Fig6. A model power system using STATCOM
controlled by conventional PI controller
D. A model Power System simulation using
STATCOM controlled by Fuzzy Logic controller
(FLC)
Fuzzy logic controller is an operative and more
precious controller than other classical controllers
like PI controller, PID controller etc. It took less
storage and it is suitable for non-linear systems. Here
it is used in the control loop of STATCOM. From the
PCC (Point of Common Coupling) the voltage Vpcc
and a reference value Vpccref is compared and the error
and change in error value is calculated and fed as
input values to the Fuzzy Controller. Fig.7 denotes
the simulation diagram of Fuzzy logic controller with
STATCOM [11] [12] & [13]

Fig7. a simple power system with STATCOM
controlled by Fuzzy Logic Controller– Simulink
diagram
1) Mamdani method: Mamdani method is used in
this work and it is computationally proficient and
more compact. The two inputs and one output
method is available in two rule system. Here the
inputs are X1 and X2 then output is represented
as Y. In this system, error and change in error are
represented as X1 and X2. The output Y is
denoted as alpha.
2) Fuzzification: Five linguistic sets of fuzzy using
triangular membership function is presented in
fig.7a&b and five sets of fuzzy variables used are
PVB (Positive Very Big), PB (Positive Big), Z
(Zero), NB (Negative Big), NVB (Negative Very
Big)
Fig8 a. error (w) and change in error (dw) – input
membership functions
Fig8 b. alpha (Y) – output membership functions
3) Defuzzification: Defuzzification is the reverse of
fuzzification. Defuzzification using weighted
average method is used in this work. The Pulse
duration is obtained as the defuzzified output.
4) Rule base: “If-then” format is used in forming
fuzzy rules. In fuzzy rule the „if‟ part is known as
rule-antecedent and the „then‟ part is called rule
consequent. The fuzzy controller increases the
pulse duration during positive error condition
and decreases the duration during negative error
condition
E. Simple Power System simulation with
STATCOM controlled by Model Predictive
controller(MPC)
Model predictive controller (MPC) concept is the
most widely used of all modern advanced control
technique in many control application. MPC has four
important tuning parameters: the weight matrix Λ,
the output weight matrix Γ, the prediction horizon P
and the control horizon M. The control horizon M is
the number of MV moves that MPC calculates at
each sampling time to remove the current prediction
error. The prediction horizon P represents the number
of samples in to the future over which MPC
computes the predicted process variable profile and
reduces the prediction error. The weighting matrix Γ
is used for scaling in the multivariable case; it
permits the assignment of more or less weight for the
objective of reducing the predicted error for the
output variable.
A dynamic system model is used in order to
forecast the controlled variables. The regulator
variables variation to predict the response of system
at each time horizon is allowed by linear vector
function.
In MPC, receding horizon concept is represented
as shown in fig.9
Fig9. Receding Horizon concept
From these graph, MPC can be expressed as
equation, when normal model is predicted by control
horizon and prediction horizon method and shows
predicted output.
In this work an attempt is made to develop a
STATCOM controller with MPC and the
performance is analyzed by using MPC toolbox in
MATLAB/Simulink. The MPC toolbox can operates
both in linear and nonlinear system model.
Simulation diagram is shown in fig 10

Fig10. A simple power system with STATCOM
controlled by Model Predictive Controller– Simulink
diagram
F. Discussion of Results and experimental
Analysis
Analysis of PI controller results
a. Without load Disturbances
Fig11. Real and reactive power waveform of
STATCOM with PI controller
Fig 11 shows the real power and reactive power
waveform of STATCOM device with PI controller.
The system settles down depending upon the gain
values of PI controller. Due to the higher values of
gain in PI controller, it causes peak overshoot in
waveform at initial condition. This waveform is
captured by using three phase active and reactive
power link block in Simulink model. Here the system
is settled at 0.06 sec for real and reactive power. The
peak overshoot value for real and reactive power is
260 MW and 151 MVAR respectively.
b. With load Disturbances
Fig 12 and fig 13 represents the waveform of
load voltage and STATCOM current when load
disturbance is occurred. In SMIB system, two RL
series load is connected as parallel in receiving end
and the three phase circuit breaker is connected in
between two RL load. The response of load voltage
and STATCOM current is getting disturbed. Here the
overshoot level of load voltage is 260 kV and
response is settled at 0.12 sec, at mean time the
overshoot value of STATCOM current is 870 A and
settled time is 0.16sec.
2. Analysis of Fuzzy logic controller results
a. Without load disturbance
Fig14. Real and reactive power waveform of
STATCOM with Fuzzy Logic controller
Now the Fuzzy logic Controller replacing PI
controller. Fig 14 displays the real and reactive power
response of STATCOM with Fuzzy logic Controller.
In that response, peak overshoot is reduced and
fastest settling time when compared to PI controller
output. The values of peak overshoot of Real and
reactive power is 138 MW and 222 MVAR, the
settling time is 0.04 sec respectively.
b. With load disturbance
Fig15. Load Voltage waveform

Fig16. STATCOM current waveform
Fig 15 and fig 16 represents the waveform of load
voltage and STATCOM current when load
disturbance is occurred. Here the overshoot level of
load voltage is 240 kV and response is settled at 0.10
sec, at the mean time the overshoot value of
STATCOM current is 485 A and settled time is 0.14
sec respectively. When compared to PI controller
response, the overshoot value of load voltage is
reduced from 260 kV to 150 kV and it reaches the
steady state from 0.12 sec to 0.10 sec respectively.
3. Analysis of Model Predictive Controller results
a. Without load disturbance power waveform of
STATCOM with Model Predictive Controller
In this case, Fuzzy logic controller is replaced by
Model Predictive Controller. Fig 17 shows the real
and reactive power response of STATCOM with
Model Predictive Controller. In that response, peak
overshoot is reduced and the settling time is faster
when compared to both Fuzzy and PI controller
output response. The values of peak overshoot of
Real and reactive power is 125 MW and 210 MVAR,
the settling time is 0.035 sec respectively.
b. With load disturbance
Fig18. Load Voltage waveform
Fig19. STATCOM current waveform
Fig 18 and fig 19 represents the waveform of
load voltage and STATCOM current during load
disturbance when STATCOM is controlled by Model
Predictive Controller. Here the overshoot level of
load voltage is 232 kV and response is settled at 0.09
sec, at the mean time the overshoot value of
STATCOM current is 418 A and settled time is 0.11
sec respectively. When compared to both PI
controller and Fuzzy logic controller response, the
overshoot value of load voltage is reduced.
Table I, table II and table III gives the
comparison of PI controller, Fuzzy Logic controller
and Model Predictive Controller of Peak overshoot
values measured for Real & Reactive power, load
current and STATCOM respectively.
TABLE I
Comparison of the Real and the Reactive power
without load disturbance
TABLE II
Comparison of load voltage when load disturbance
occurs
TABLE III
Comparison of STATCOM current when load
disturbance occurs

IV. CONCLUSION
In this paper the STATCOM control scheme for
the Single-Machine Infinite Bus (SMIB) system to
improve transient stability is simulated using
MATLAB/Simulink in power systems block set. The
Simulation models of PI, FLC and MPC were
developed. The Performance of different controllers
is analyzed for a load disturbance. When comparing
the results, performance of PI controller with
STATCOM, gives high peak overshoot and more
settling time. Performance of fuzzy logic controller
with STATCOM, gives low peak overshoot and
quick settling time when comparing the results with
PI controller. The Response of Model Predictive
controller with STATCOM, the values of peak
overshoot and settling time is found to be lower than
the results of FLC with STATCOM. Thus MPC
provide better control in transient stability
improvement of the simulated power system
REFERENCES
[1] N. G. Hingorani and L. Gyugy,
Understanding FACTS, Concepts and
Technology of Flexible AC Transmission
System, Wiley- IEEE press, 1 Ed., Dec.
1999.
[2] N.G. Hingorani, High power electronics and
flexible AC transmission system, IEEE
Power Engineering review, Vol. 8, 1988.
[3] N. G. Hingorani, “Flexible AC Transmission
Systems (FACTS) – Overview, IEEE
Spectrum”, Vol.30, No.4, pp. 40 – 45, April
1993.
[4] C.Schauder , H.Mehta, “Vector analysis and
control of advanced static var
compensator,” IEE proceedings., vol. 140,
pp. 299-306 July 1993.
[5] P.W. Lehn., M.R.Iravani., "Experimental
Evaluation of STATCOM Closed loop
Dynamics", IEEE transactions on Power
Delivery, Vol. 13, No. 4, pp.1378-1384
October 1998.
[6] M.Mohammadha Hussaini, Dr. R. Anita,
“Dynamic Response Of Wind Power
Generators Using Statcom”, International
Journal of Engineering and Technology,
Vol.2 (4), 297-304, 2010.
[7] Surinder Chauhan, Vikram Chopra, Shakti
Singh, “Transient Stability Improvement of
Two Machine System using Fuzzy
Controlled STATCOM”, International
Journal of Innovative Technology and
Exploring Engineering (IJITEE) ISSN:
2278-3075, Volume-2, Issue-4, March 2013
[8] Ben-Sheng Chen, Yuan-Yih Hsu, Senior
Member, IEEE "An Analytical Approach to
Harmonic Analysis and Controller Design
of a STATCOM" IEEE Transactions on
Power Delivery VOl. 22 No. 1 January
2007.
[9] Nitus Voraphonpiput and Somchai
Chatratana, “STATCOM Analysis and
Controller Design for Power System Voltage
Regulation”, IEEE/PES Transmission and
Distribution Conference, pp.,1-6, China,
2005.
[10] P.W.Lehn, “Exact modeling of the voltage
source converter”, IEEE Transactions on
Power Delivery, Vol.17, Issue. 1, pp. 217 -
222, Jan. 2002.
[11] B. Singh, R. Saha, A. Chandra, K. Al-
Haddad, “Static synchronous compensators
(STATCOM): a review”, IET Power
Electron., Vol. 2, Issue. 4, pp. 297–324,
2009.
[12] S. Arockia Edwin Xavier, P. Venkatesh, M.
Saravanan, “Development of PI and Fuzzy
Controllers for STATCOM in dSPACE
Environment”, European Journal of
Scientific Research, ISSN 1450-216X
Vol.75 No.2, pp. 216-227, 2012.
[13] S. Arockia Edwin Xavier, P. Venkatesh, M.
Saravanan, “Development of Intelligent
Controllers for STATCOM”, IEEE Power
System Technology Conference, pp.1-7, 12-
15 Oct, 2008.

Power System Stability Enhancement Using FLC and MPC for STATCOM

Recommended

More Related Content

What's hot (19)

Similar to Power System Stability Enhancement Using FLC and MPC for STATCOM (20)

Recently uploaded (20)

Power System Stability Enhancement Using FLC and MPC for STATCOM