IMPLEMENTATION OF LANE TRACKING BY USING IMAGE PROCESSING TECHNIQUES IN DEVELOPED PROTOTYPE AUTONOMOUS VEHICLE

The International Journal of Multimedia & Its Applications (IJMA) Vol.11, No. 4/5/6, December 2019
DOI:10.5121/ijma.2019.11601 01
IMPLEMENTATION OF LANE TRACKING BY USING
IMAGE PROCESSING TECHNIQUES IN DEVELOPED
PROTOTYPE AUTONOMOUS VEHICLE
Sertap Kamçı, Dogukan Aksu and Muhammed Ali Aydin
Computer Engineering Department, Istanbul University-Cerrahpasa,
Istanbul, Turkey
ABSTRACT
Today, unmanned vehicle technologies are developing in parallel with increasing interest in technological
developments. These developments aim to improve people's quality of life. Transportation, which is a part
of human life, has taken its share from this developing technology. With the development of artificial
intelligence, it is aimed to provide the necessary assistance to the driver in transportation and to provide
ease of driving. This development has been increased with ADAS (Advanced Driver Assistance Systems) in
vehicles, but it is not possible to experience a completely driverless and comfortable road. With all these
demands and conditions, autonomous vehicles have quickly attracted attention. While ADAS is a warning
system, all accident risks that may arise from the driver rather than the warning to the driver in
autonomous vehicles are minimized by the vehicle.
In this paper, we present an autonomous vehicle prototype that follows lanes via image processing
techniques, which are a major part of autonomous vehicle technology. Autonomous movement capability is
provided by using various image processing algorithms such as canny edge detection, Sobel filter, etc. We
implemented and tested these algorithms on the vehicle. The vehicle detected and followed the determined
lanes. By that way, it went to the destination successfully.
KEYWORDS
Autonomous Vehicle, Lane Detection, Image Processing, HSV Color, RGB Color, Canny Edge
Detection, DC Motor, Region of Interest (ROI), Vanishing Point, Sobel Filter
1. INTRODUCTION
In order for the vehicles to be able to watch safely in a series, the part of the vehicle path
separated by lines is called lane. A good lane monitoring enhances the enjoyment of going on the
road. Solving heavy traffic and solving other disruptions can become more streamlined with
drivers taking some responsibility. If an autonomous vehicle is not traveling, the driver should:
After providing the road and traffic control without deciding to pass the vehicle, first to check the
mirrors according to the direction of departure, to check whether there is a vehicle in the blind
spot and wait for the vehicles to pass, to give the appropriate signal to the direction of exit, not to
get too close to the passing vehicle and after passing the vehicle to pass immediately, to overtake
in cases where overtaking is prohibited, service vehicles and buses minibuses briefly public
transport vehicles to pay attention to the superiority of the transition. In addition to all these
responsibilities, it is also not necessary to test how dangerous overtaking is wrong. It is also
important to not leave the current lane and center the lane. Because in this case the accident is
inevitable and people in other vehicles have added to the risk of having an accident. But thanks to
autonomous vehicles, the passengers pass a comfortable journey without the need of the driver's
responsibilities.

2
The algorithm of autonomous vehicles allows the protection of the lane. Gets an idea with the
algorithm written about the lanes to be traveled according to the route of the vehicle and
determines the path accordingly. The vehicle has an idea about the lanes to be traveled according
to the route of the vehicle and determines its path accordingly.
The algorithm in the study is on lane tracking. The algorithm is designed to track lanes. First of
all, with the operation of the autonomous vehicle, the image on the road is taken through the
camera. The received image is a video image and is divided into image frames called frames.
Using specific image processing algorithms, the lanes in these frames are detected. When the
determination of the lane, the vehicle is given the instructions to continue straight to the vehicle
according to the angles determined by the lane and to turn right or left.
This paper is organized as follows: Section 2 contains relevant studies and provides a
comprehensive overview of the different detection methods that are used to the project. The
functions and models used in Chapter 3 are presented. The experience gained in Chapter 4 is
explained and the project output is given. In Chapter 5, the operating logic of the car following
the lane is explained with a flow diagram. The results obtained are given in Chapter 6.
2. RELATED WORKS
The interest in autonomous vehicles has been increasing rapidly in recent years. In this paper,
image processing algorithms for lane detection and tracking are mentioned.
There are several techniques for performing lane detection [1,2]. First of all, the image processing
methods used in the project should be examined to find the lines. Thereafter, lines should be
identified from image frames where image processing techniques are applied. After this step, the
ROI between the lines should be found. In addition, a virtual line is drawn in the middle of these
lines to make the path look like a curve. With this curve, the bend of the way is determined by
finding the angle. With this angle, the vehicle has an angle of movement and the vehicle moves in
a straight, right-handed, left-handed direction according to the specified angle.
In this paper, we examine the related studies in three stages. These steps are: image processing
techniques, detecting lane lines and finding ROI.
2.1. Image Processing Techniques
In the design of the algorithm, firstly the mutation from RGB color space to HSV color space is
made. According to some studies, it is more convenient to use HSV color space when we want to
differentiate an object of a certain color in any computer vision/image processing application [3].
In addition, the HSV color space provides clarity of the colors in the image. HUE is also used to
distinguish colors more clearly.
Color images contain more information than gray level images. For this reason, in some related
studies, the edge detection process for color images has been examined. Grayscale method is one
of these methods. The cost of detecting ROI in the image was reduced by the Grayscale image
conversation method and the process was accelerated [4,5].
2.2. Determination of Lane Lines
Canny edge detection, Hough transformation and Sobel filter methods are the methods used to
find the lane lines.

3
Canny edge detection is a method of edge detection. The lanes are lines and edges and the
purpose is to discover optimal edge detection. In this way, the edges in the image as well as
unwanted noise called pixels to eliminate the full image recognition is done [6]. Hough
transformation method is a method that finds and shows shapes. Since the lane lines have a shape,
lane lines can be found by the Hough transform method [7].
Sobel filter method is a separate method used to find the edge.
It is seen in all the studies obtained the use of the edge detection algorithm in images with a
grayscale colour space is closer to the edge information in the actual image.
2.3. Finding Region of Interest (ROI)
The area of the lane is called the ROI. While some algorithms have an ROI up to the point where
the lines can be detected by combining the lane lines in the image, some algorithms have methods
for finding the ROI based on vanishing point detection techniques [8].
There are two common methods for the detection of ROI. Firstly, left and right lane lines are
found. In the first method, the lane lines are stretched and intersect at one point. A triangular
region is formed. The area within the triangular region up to the region where the lane are
detected forms a rectangular region. This field returns the ROI. The deviation difference of the
angles and the obtained region is calculated and the direction of the path is calculated [9,10].
Another method is to determine the ROI by determining the skyline. Horizon line is the line
where the earth globe and sky intersect when viewed in nature. With the determination of the
horizon line, the lane lines are also combined and the intersecting area shows the ROI.
3. DESIGN OF THE LANE FOLLOWING AUTONOMOUS CAR
The design part of the car is divided into two parts. These are the movement of the software and
the hardware of the vehicle. The software field is algorithm design and coding.
3.1. Software
The designed code has a layered architecture. There is a python file with a main structure named
Main. Methods in other Python files are imported and run by calling the methods respectively.
The lane lines must be determined in the algorithm of the car following the lane. For this, lane
detection algorithm is used. Image processing techniques are used in the lane detection algorithm.
These image processing techniques are described in the below.
Some libraries used for image processing are: Numpy, OpenCV, Math, RPI.GPIO. The Numpy
library was used for sequencing. This array operations; dividing the video video taken from the
camera into frames and keeping them in a sequence, keeping the curves of the lane lines in the
frames in one sequence, keeping the inclination angles of the road in the forward path in a
sequence. The Math library is used to perform mathematical operations in the algorithm. The
OpenCV library focuses on image processing, video capture and analysis, including features such
as face detection and object detection. This library was used to detect objects and lanes in the
image. The RPI.GPIO library is used to manage the pins on the raspberry pi and to locate the
wheels, sensors and batteries that we have connected in the algorithm.
Frames with original RGB color space were converted to frames with HSV color space and color
saturation was gained. These frames have been rendered grayscale image processing so that an
image with saturated color characteristics are converted to shades of gray more clearly. If this was

4
done without converting from the RGB color space to the HSV color space, the frame converted
to grayscale would receive shades of gray with less transition and the details of the clear shapes
on the frame would not be visible.
The Canny edge detection method was used on the grayscale frame and the lines including the
detailed lines in the frame were reached. After these image processing methods, the lanes in the
original path obtained were detected. The lanes were determined by Hough Transform and Sobel
filter methods [11,12].
For the car to go in the middle of the lanes, there is a variable called center lane in the code, and
the centerline is a line that centers the two lanes [13]. Here you must first find the right and left
lanes, and the mainline of code written for the detection of the left lane is as follows.
left_fit_average = np.average (left_fit, axis = 0)
left_line = make_coordinates (image, left_fit_average)
The following mainline of code is written for Centerline.
lines = cv2.HoughLinesP (frame, 2, np.pi / 180, 100, np.array ([]), minLineLength = 40,
maxLineGap = 5)
For the centerline, the following line of code is written.
center_lines = average_slope_intercept (frame, lines)
The algorithm written for ROI detection is called here and the calculation of the ROI is done in
this algorithm. The ROI-finding algorithm maintains the intersecting and polygon definition
region on the image. This is the area between the lane and the horizon.
(a) Original frame (b) HSV frame
(c) Grayscale frame (d) Canny Edge Frame
Figure 1. Steps of image processing methods on a path

5
In Figure 1 (a), a path with RGB color space was converted to HSV color space as in Figure 1 (b).
Color saturation increases with HSV color space. Then, the image was processed as shown in
Figure 1 (c) using Gaussian Blur and Gray Scale methods.Gaussian Blur allows us to adjust the
degree of blurring, creating effects ranging from slightly softening the image to covering the
entire image with thick fog. Gaussian Blur is also a successful filter to protect the edges in the
image [14]. Figure 1 (d) is used to understand the line of the lanes on the road by using Canny
edge detection and Hough Transform methods. As a result of the calculations, the lane lines are
perceived as shown. In Figure 2-a, a re- converted image frame is given to the RGB image. In
Figure 2-b, an image frame that is not converted to RGB color space is given.
The mainlines of code and descriptions of the steps in Figure 1 are given below. The main line of
code for conversion from RGB color space to HSV color space is as follows. Cv2 in this code
represents the Opencv library. COLOR_BGR2HSV is the command to switch from RGB color
space to HSV color space.
hsv = cv2.cvtColor (crop, cv2.COLOR_BGR2HSV)
The command line below is the command to convert the frame from HSV color space to
Grayscale.
gray = cv2.cvtColor (image, cv2. COLOR_HSV2GRAY)
In order to find the lines in the grayscale frame with the following lines of code, the Canny edge
detection image processing method is used.
canny_imag A = canny (frame)
cropped_imag A = region_of_interest (canny_imag A)
(a) Original path image (b) Detected Lane from image
(c) Detected interested lane (d) ROI of the path image
Figure 2. Detection of lanes in a sample path

6
In Figure 2 (a), the algorithm is written to detect the road where the vehicle is located and this
lane is shown based on the nearest lane. In Figure 2 (b), the ROI of the lane was found. In Figure
2-c, the algorithm is written to detect the path where the vehicle is located and this lane is shown
based on the nearest lane. Figure 2-d shows the ROI of the lane.
3.2. The Movement of the Vehicle
We want the vehicle to the center the lanes before start moving. In the code, the function that
generates the virtual line is written to center. Then you need to follow the lane where it is located.
For tracking of the lane, the ROI has the angle of rotation of the lane. When driving straight
ahead, the vehicle is commanded to continue straight ahead. We used DC motors for the
movement of the vehicle.
GPIO.output(Motor1A,GPIO.LOW)
Above left is the left motor stop command. In the same way, the right engine must be stopped for
a right turn. This stop command may be slightly different, if the vehicle is not going to turn
completely and rotating at a different degree than the angle of 180, the motor in the direction of
rotation is decelerated and the motor in the other direction is accelerated. This is the logic of the
vehicle's progress and rotation relative to the road.
Figure 3. Image of autonomous vehicle prototype
4. EXPERIMENTS
A great experience has been gained in the construction of this project. Before the integration of
the code to the vehicle, the code was checked by remote movement with the computer. Then the
code is integrated into the vehicle. The desired result is to obtain and process the image from the
camera and to find the lanes correctly. The vehicle should also be able to move smoothly with
commands sent from raspberry pi without deviating from its path. The pre-integration and post-
integration operation of the code was verified and successfully completed.
5. THE PROPOSED METHOD

7
Algorithm. Pseudocode for the proposed method
Figure 4. The proposed method: The Flowchart and The Pseudocode.
The figure above shows the algorithm-based operation designed in the period from the start of the
vehicle to the closing of the vehicle.
When the vehicle is started, the camera also operates (Scheme1) and instant frames (frames) are
taken from the camera (Scheme2). Lanes are detected by image processing methods and ROI is
found (Scheme3). When the ROI is found, it is understood how the vehicle should be directed to
protect the lane and there is an angle for this (Scheme 4). The angle found is adjusted by the
speed of the right and left motors (Figure 5). As long as the vehicle is not switched off, the
camera operates and returns to Scheme2, resulting in a flow loop. If the vehicle is switched off
(Scheme6 takes yes), the flow switches to Scheme7 and the autonomous vehicle and camera are
switched off.
6. CONCLUSION
In this paper, an autonomous vehicle prototype that detect lanes via image processing techniques,
which are a major part of autonomous vehicle technology is presented. Some image processing
algorithms such as canny edge detection, Sobel filter, etc. are used to provide autonomous
movement capability. They were implemented and tested on our prototype vehicle. The prototype
vehicle detected and followed the determined lanes successfully and it reached the destination. As
a future work, we are planning to use generative neural networks, deep learning, and various
machine learning algorithms to detect lane and traffic signs together.
ACKNOWLEDGEMENTS
The project in this paper is presented as a bachelor thesis and it is supported by Istanbul
University-Cerrahpasa Scientific Research Projects Commission as project number 32561 and
“FBA-2019-33004”. We would like to thank Istanbul University-Cerrahpasa Scientific Research
Projects Unit for their support.
REFERENCES
[1] David C. Andrade, Felipe Bueno, Felipe Franco, Rodrigo A. Silva, Student Member, IEEE, João H.
Neme, Erick Margraf, Student Member, IEEE, William Omoto, Felipe Farinelli, Angelo M. Tusset,
Sergio Okida, Max M. Santos, Senior Member, IEEE, vel Strategy for Road Lane Detection and
Tracking based on Vehicle’s Forward Monocular Camera”, IEEE Transactions on Intelligent
Transportation Systems, September 2018.
[2] Aharon bar hillel, Ronen Lerner, Dan Levi, Guy Raz, “Recent progress in road and lane detection: A
survey”, Machine Vision and Applications 2011.
[3] Gurjashan Singh Pannu, Mohammad Dawud Ansari, Pritha Gupta,” Design and Implementation of
Autonomous Car using Raspberry Pi”, International Journal of Computer Applicationa, 9 March 2015.

8
[4] Peerawat Mongkonyong, Chaiwat Nuthong, Supakorn Siddhichai, Masaki Yamakita, “Lane detection
using Randomized Hough Transform”, 8th TSME-International Conference on Mechanical
Engineering, January 2018.
[5] A.A.M. Assidiq, Othman O. Khalifa, Md. Rafiqul Islam, Sheroz Khan, “Real time lane detection for
autonomous vehicles”, IEEE Xplore, 2008.
[6] Anjali Goel, “Lane Detection Techniques - A Review”, International Journal of Computer Science
and Mobile Computing, February 2014.
[7] Ze Wang , Weiqiang Ren “LaneNet: Real-Time Lane Detection Networks for Autonomous Driving“,
ArxİV,4 July 2018
[8] CHANG YUAN, HUI CHEN , JU LIU , DI ZHU , AND YANYAN XU, “Robust Lane Detection for
Complicated Road Environment Based on Normal Map”, IEEE, July 27th 2018.
[9] Sertap Kamçı, Aylin Yazıcı, Bilge Kamberoğlu, Doğukan Aksu, Muhammed Ali Aydın, “A Survey of
Lane Detection and Traffic Signs Recognition for Autonomous Vehicles”, Akademik Bilişim’2019,
Ordu Üniversitesi Bilim ve Teknoloji Dergisi, 2019.
[10] Qingquan Li, Jian Zhou, Bijun Li, Yuan Guo, Jinsheng Xiao, “Robust La”, Dec 2018 ne- Detection
Method for Low-Speed Environments”, MDPI, Dec 2018.
[11] Thittaporn Ganokratanaa , Mahasak Ketcham, Sasipa Sathienpong, “Real-Time Lane Detection for
Driving System Using Image Processing Based on Edge Detection and Hough Transform”,
International Conference on Digital Information and Communication Technology and its
Applications, 2013
[12] Nur Shazwani Aminuddin, Masrullizam Mat Ibrahim, Nursabillilah Mohd Ali, Syafeeza Ahmad
Radzi, Wira Hidayat Mohd Saad & Abdul Majid Darsono, “A New Approach to Highway Lane
Detection by Using Hough Transform Technique”, 2 (Dec) 2017, Journal of IC
[13] C.Y. Kuo, Y.R. Lu and S.M. Yang , “On the Image Sensor Processing for Lane Detection and Control
in Vehicle Lane Keeping Systems”, US National Library of Medicine National Institutes of
HealthNCBI, April 2019
[14] Gurveen Kaur, Dinesh Kumar, “Lane Detection Techniques: A Review”, International Journal of
Computer Applications, IJCA Journal, 2015.
AUTHORS
Sertap Kamçı completed her primary school education in Incirli Bahçe Primary School. She
completed her secondary school education at the Siir Mektebi Primary School and his high
school education at Gungoren Anatolian High School. She graduated Istanbul University-
Cerrahpasa Faculty of Engineering Computer Engineering at 2019.
Dogukan Aksu received his B.S. and M.Sc. degrees in Computer Engineering at Istanbul
University in 2015 and 2018 respectively. He is a PhD student in Computer Engineering. His
research interests are information and network security, cryptography, artificial intelligence,
machine learning and image processing.
Muhammed Ali Aydin completed his B.S. in 1997-2001 in Computer Engineering at
Istanbul University, M.Sc. in 2001-2005 in Computer Engineering at Istanbul Technical
University and Ph.D. in 2005-2009 Computer Engineering at Istanbul University. His
research interests are communication network protocols, network architecture, cryptography,
information security and network security.

IMPLEMENTATION OF LANE TRACKING BY USING IMAGE PROCESSING TECHNIQUES IN DEVELOPED PROTOTYPE AUTONOMOUS VEHICLE

Recommended

More Related Content

What's hot (18)

Similar to IMPLEMENTATION OF LANE TRACKING BY USING IMAGE PROCESSING TECHNIQUES IN DEVELOPED PROTOTYPE AUTONOMOUS VEHICLE (20)

Recently uploaded (20)

IMPLEMENTATION OF LANE TRACKING BY USING IMAGE PROCESSING TECHNIQUES IN DEVELOPED PROTOTYPE AUTONOMOUS VEHICLE