The iot academy_embeddedsystems_training_basicelectronicspart1

THE IOT ACADEMY
BASIC ELECTRONICS

Basic Electronics (Outline)
The Components of Electricity
Volt-Ohm-Meter Basics (Measuring Electricity)
Circuit Diagrams Basics (Electronic Roadmaps)
The Resistor
Ohm’s Law
The Capacitor
The Inductor
The Diode
The Transistor (Electronic Valves)

The Components of Electricity
 Voltage
 Current
 Resistance
 Types of Current: AC and DC
 Circuits
 Close
 Open
 Short

Voltage, Current, and Resistance
 Water flowing through a
hose is a good way to look
at electricity
Water is like Electrons in a wire
(flowing electronsis called
Current)
Pressure is theforce pushing water
througha hose – Voltage is the
force pushing electronsthrough
a wire
Friction againstthe holewallsslows
the flow of water– Resistance
is the force that slows the flow
of electrons

Types of Current
 There are 2 types of current
 The type is determined only by the direction the
current flows through a conductor
 Direct Current (DC)
 Flows in only one direction negative toward positive
pole of source
 Alternating Current (AC)
 Flows back and forth because the poles of the source
alternate between positive and negative

Circuits
 A circuit is a path for current to flow
 Three basic kinds of circuits
 Open – the path is broken and interrupts
current flow
 Close – the path is complete and current flows
were it is intended
 Short – the path is corrupted in some way and
current does not flow were it is intended

Volt-Ohm-Meter Basics
(Measuring Electricity)
 Common Functions
 Voltage
 AC/DC
 Ranges
 Current
 AC/DC
 Ranges
 Resistance
 Ranges
 Continuity
 Semi-conductor
Performance
 Transistors
 Diodes
 Capacitance

Meter Reading Digits
DC Voltage Scales
AC Voltage Scales
Probes
Function Selection

Resistance
DC Current (low)
DC Current (high)
Transistor Checker
Diode Checker

(Measuring Electricity)
Measuring voltage
Voltagetype
Scaling
Safety
 Physical (personal)
 Equipment
Measuring current
Current type
Scaling
Safety
 Physical (personal)
 Equipment
Measuring resistance
Scaling

Measuring voltage
 Voltage type – DC and AC
 When measuring voltage, the meter probes are
placed across the voltage source.
 The VOM uses two separate functions and ranges to
measure DC and AC.
 Because AC is a constantly changing wave form,
measuring AC voltages is not a simple matter.
 This VOM measures pseudo-RMS voltages

Measuring voltage
 Meter Set-up
 Scale set to highest
predictable
 Probes into right
jacks
 Note voltage polarity
+

Measuring Voltage
 Set-up VOM on 600V DC
Scale
 Touch red probe to (+)
 Touch black probe to (–
)
 Read voltage to nearest 1
volt

Measuring Voltage
 Now touch the red
probe to (-)
 Touch the black probe
to (+)
 Read voltage to
nearest 1 volt, note the
minus sign that
signifies a negative
voltage

Measuring Voltage
Scale
)
 Read voltage to nearest .1
volt

Measuring Voltage
Scale
)
 Read voltage to nearest .01
volt

Measuring Voltage
Scale
 Touch black probe to (–)
 Using a 1.5 volt battery -
read voltage to nearest .01
volt

Measuring Voltage
Set-up VOM on 2000mV
DC Scale
This scale is reading 2000
milli-volts
(or 2 volts)
Touch red probe to (+)
Touch black probe to (–)
Using a 1.5 volt battery - read
voltage to nearest .001 volt

Measuring Voltage
 Set-up VOM on 2000m V
DC Scale
)
 Using a 9 volt battery
 This is clearly an over-
voltage situation, note
the reading.

Measuring Voltage - Safety
 When measuring voltage, the voltage being
measured is exposed to the operator and flowing
through the probes. Be cautious, be attentive,
watch what you touch!
 The probes have sharp points so that you can make
precise contacts. Use the protective shields when
probes not in use.
 Observe the meter maximum limits for voltage and
current. Fuses are a last resort protection feature.
If you blow a fuse, you made a mistake!

Measuring Current
 There is greatest potential for meter damage when
measuring current than any other function.
 Just as in voltage, there is two kinds of current
associated with the voltage, AC and DC
 This meter will only measure DC, more expensive
meters will measure both currents
 To measure current, the VOM must be inserted
into the circuit so that the current flows through
the meter.

Measuring Current
 There are two current ranges, high – up to 10
amps, and low – 200 milliamps (.2 amps) and
below.
 Internal fuses provide some meter protection for
over current situations.
 Because there is such a wide range of current scales,
there are two physical probe jacks for the two ranges
 This allows for better protection, a hardy fuse to handle
up to 10 amps of current and a more fragile fuse to
protect the sensitive circuits needed to measure small
currents.

Measuring Current
 CAUTION!!!!!!! There must be some resistance
in the circuit or the current flow through the
circuit will be the maximum the source will
produce, AND THIS CURRENT LEVEL
COULD DAMAGE THE VOM!
 In other words, DO NOT CONNECT THE
VOM PROBES DIRECTLY ACROSS THE
BATTERY POLES IN THE CURRENT
MEASURMENT FUNCTION!

Measuring Current
 We will be using some concepts during the
current measurement exercises that will be
covered in more detail later, so be patient, it
will all come together in the end.
 In the following exercises you will use various
resistors to limit the current flow in a simple
circuit.

Measuring Current
Basic Circuit
Battery
VOM
+-

First Current Measurement
 Set up the circuit using a
100 ohm resistor (brown,
black, brown).
 Connect a wire to the +
power source, connect
another wire to the top end
of the resistor (the non
grounded end).
 Set VOM current scale to
200m.
 Without connecting the
battery, practice touching
the VOM probes to the
exposed wire ends.

 Connect the battery.
 With the VOM set to the
200m current scale, touch
the black lead to the wire
hooked to the high side of
the resistor.
 Touch the red lead to the
lead coming from the +
side of the battery.
 Note the VOM reading.

 Now reverse the
VOM leads and
note the reading.

 Return the VOM leads so
that the red is connected
to the battery.
 Change the VOM current
ranges down and note the
display readings
 What is the best range for
measuring the current
from a 9 volt source
through a 100 ohm
resistor?
200m Range
20m Range

Measuring Current
 Wire the circuit
with a 1k ohm
resistor (brown,
black, red).
 Measure current
with 200m range.

Measuring Current
 What is the best
range to measure
the current through
a 1 k resistor?
200m
20m
2000u

Measuring Current
 Wire the circuit with a
10 k ohm resistor
(brown, black, orange).
 Measure current with
the 2000u range.

Measuring Current
 What is the best
range to use to
measure the
current through a
10 k ohm resistor at
9 volts?
2000u
200u

Measuring Current
Wire the circuit
with a 100 k ohm
resistor (brown,
black, yellow).
Begin with the
2000m range, and
measure the current
at each range.
What is the best
range to use to
measure the current
trough a 100 k ohm
resistor at 9 volts?

Measuring Resistance
When the VOM is used to measure resistance,
what actually is measured is a small voltage and
current applied to the component.
There are 5 ranges, an out of resistance reading
will indicate a single 1 digit. Remember k means
multiply the reading by 1000.
Operating voltages should be removed from
the component under test or you could damage
the VOM at worst, or the reading could be false
at best.

 Disconnect the battery
from the board,
remember to measure
resistance the circuit
should be un-powered.
 Put the 100 ohm
resistor in place, no
additional wires are
required.
 Select the 200 range
and touch the probe
leads to either side of
the resistor.

 Now reverse the probe
leads and observe the
reading.
 Any difference?

 Now using the 100 ohm
resistor, measure the
resistance using each of
the other ranges.
 Note that the resolution
of the reading decreases
as the maximum ohm
reading increases, down
to the point where it is
difficult to get a good
resistance reading.
2000
20k
200k
2000k

 Now use the 1k ohm
resistor and the 200
range.
 Explain the reading
you observe.
 Find the appropriate
range to measuring
1,000 ohms (1k).
200
2000

Circuit Diagrams Basics
(Electronic Roadmaps)
 Component Representations
 Resistor
 Ground
 Capacitor
 Inductor
 Diode
 Transistor
 Integrated circuit
 Miscellaneous

Integrated circuit
2
3
4
5
13
12
11
10
7 8
1 14
6 9

The Resistor
 Resistance defined
 Resistance values
 Ohms – color code interpretation
 Power dissipation
 Resistors in circuits
 Series
 Parallel
 Mixed

Resistance Defined
 Resistance is the impediment to the free flow of
electrons through a conductor
 (friction to moving electrons)
 Where there’s friction, there is heat generated
 All materials exhibit some resistance, even the best
of conductors
 Unit measured in Ohm(s)
 From 1/10st of Ohms to millions of Ohms

Resistor Types
 Fixed Value
 Variable value
 Composite resistive material
 Wire wound
 Two parameter associated with resistors
 Resistance value in Ohms
 Power handling capabilities in watts

Reading Resistor Color Codes
1. Turn resistor so gold or silver band is at right
2. Note the color of the two left hand color
bands
3. The left most band is the left hand value digit
4. The next band to the right is the second value
digit
5. Note the color of the third band from the left,
this is the multiplier
6. Multiply the 2 value digits by the multiplier

Reading Resistor Color Codes
(Practice Problems)
1. Orange, orange, red?
2. Yellow, violet, orange?
3. Brown, black, brown?
4. Brown, black, green?
5. Red, red, red?
6. Blue, gray, orange?
7. Orange, white, orange?

Power dissipation
 Resistance generates heat and the component
must be able to dissipate this heat to prevent
damage.
 Physical size (the surface area available to
dissipate heat) is a good indicator of how much
heat (power) a resistor can handle
 Measured in watts
 Common values ¼, ½, 1, 5, 10 etc.

Resistors in Circuits
Series
 Looking at the current
path, if there is only one
path, the components
are in series.

Series
nRRR  21

Resistors in Circuits Series
 On your proto board set
up the following circuit
using the resistance values
indicated on the next
slide.
 Calculate the equivalent
resistant RE and measure
the resistance with your
VOM
R1
R2

Series
R1 R2 Calculated
RE
Measured
RE
100 100
100K 10K
4.7K 4.7K
330 4.7K

Resistors in Circuits Parallel
 If there is more than
one way for the
current to complete
its path, the circuit is
parallel

21
21
RR
RR
 nRRR
111
1
21


On your proto board
set up the following
circuit using the
resistance values
indicated on the next
slide.
Calculate the
equivalentresistant RE
and measure the
resistance with your
VOM
R1
R2

R1 R2 Calculated
RE
Measured
RE
100 100
100K 10K
4.7K 10K
330 4.7K

Resistors in Circuits (Parallel
Challenge)
 Make a circuit with 3 resistors in parallel, calculate
the equivalent resistance then measure it.
 R1 = 330
 R2 = 10K
 R3 = 4.7K

Mixed
 If the path for the
current in a portion
of the circuit is a
single path, and in
another portion of
the circuit has
multiple routes, the
circuit is a mix of
series and parallel.
Series
Parallel
Series
R

Resistors in Circuits Mixed
 Let’s start with a
relatively simple
mixed circuit. Build
this using:
 R1 = 330
 R2 = 4.7K
 R3 = 2.2K
R1
R2
R3

Resistors in Circuits (Mixed)
 Take the parallel
segment of the
circuit and calculate
the equivalent
resistance:
R1
R2
R3
32
32
RR
RR


 We now can look at
the simplifiedcircuit
as shown here, the
parallel resistors have
been replaced by a
single resistor with a
value of 1498 ohms.
 Calculate the
resistance now of this
series circuit:
ERR 1
R1
RE=1498

In this problem,
dividethe problem
into section, solve
each section and then
combine them all
back into the whole.
R1 = 330
R2 = 1K
R3 = 2.2K
R4 = 4.7K
Series
Parallel
Series
R1
R2
R3
R4

Mixed
 The final calculations
involve R1 and the new RE
from the previous parallel
calculation.
 R1 = 330
 RE = 1.9K
R1
RE
ERR 1

Ohm’s Law
 The mathematical relationship
 E (or V)=I*R
 Doing the math
 kirchhoff’s Law
 A way to predict circuit behavior
 It all adds up
 Nothingis lost

Ohm’s Law
 There is a
mathematical
relationship between
the three components
of electricity. That
relationship is Ohm’s
Law.
 E = volts
 R = resistance in ohms
 I = current in amps
RIE *
I
E
R 
R
E
I 

Ohm’s Law
 This is the basic
circuit that you
will use for the
following
exercises.
 The VOM will be
moved to
measure
voltage/resistanc
e and current.
A
V

Ohm’s Law Exercise 1
 Wire this circuit using
a 100 ohm resistor.
 Without power
applied measure the
resistance of the
resistor.
 Connect the 9 volt
battery and measure
the voltage across the
resistor.
 Record your data.
V

 Using the voltage and
resistance data in
Ohm’s Law, calculate
the anticipated
current.
 Example data results
in a current of .09
amps or 90 milli-
amps
R
E
I 
ohms
volts
amps
1.98
8.8
09. 

 Insert the VOM into
the circuit as indicated
in this diagram.
 Using the appropriate
current range, measure
the actual current in
the circuit.
 How does the current
compare to your
prediction using Ohm’s
Law?
A

Select the 1K ohm resistor
and create the illustrated
circuit.
Pretend for this exercise
that you do not know what
the voltage of the battery is.
Measure the resistance with
power removed and then
the current with power.
Record your data.
A

 Using the current and
resistance data in Ohm’s
Law, calculate the
anticipated voltage.
 Example data results in a
voltage of 9.73 volts
RIE *

Connect the VOM into
the circuit as indicated
in this diagram.
Using the appropriate
voltage range, measure
the actual voltage
across the resistor.
How does the current
compare to your
prediction using
Ohm’s Law?
V

 In this exercise you
will use an unknown
resistor supplied by
your instructor.
 Create the circuit
illustrated and
measure the voltage
and current.
 Record your data.
V
A

 Using the voltage and
current data in Ohm’s
Law, calculate the
unknown resistance.
 Example data results
in a resistance of 3844
ohms. I
E
R 

Ohm’s Law In Practice
 The next series of exercises will put Ohm’s Law
to use to illustrate some principles of basic
electronics.
 As in the previous exercise you will build the
circuits and insert the VOM into the circuit in
the appropriate way to make current and
voltage measurements.
 Throughout the exercise record your data so
that you can compare it to calculations.

 Build up the
illustrated circuit.
 R1 = 1K
 R2 = 1K
 R3 = 2.2K
 R4 = 300
 Measure the current
flowing through the
circuit.
R1
R2
R3
R4
A

 Now move the VOM
to the other side of
the circuit and
measure the current.
 The current should
be the same as the
previous
measurement.
A

 Insert the VOM at
the indicated
location and
measure the
current.
 There should be no
surprise that the
current is the same.
A

 Measure the voltage
across R1.
 Using Ohm’s law,
calculate the voltage
drop across a 1K
ohm resistor at the
current you
measured
 Compare the result.
V

In this next step, you
will insert the VOM in
the circuit at two
places illustrated at
the right as #1 and #2.
Record your current
readings for both
places.
Add the currents and
compare and contrast
to the current
measured entering the
total circuit.
A A
#1 #2

 Using the current measured through #1 and the
resistance value of R2, 1k ohms, calculate the
voltage drop across the resistor.
 Likewise do the same with the current measured
through #2 and the resistance value of R3, 2.2k
ohms.
 Compare and contrast these two voltage values

across the parallel
resistors and record
your answer.
 Compare and
contrast the voltage
measured to the
voltage drop
calculated.
V

 In the next step, insert
the VOM into the
circuit as illustrated,
measure and record the
current.
 Compare and contrast
the current measured to
the total current
measured in a previous
step.
 Were there any
surprises?
A

Using the current you just
measured and the
resistance of R4 (330
ohms), calculate what the
voltage drop across R4
should be.
Insert the VOM into the
circuit as illustrated and
measure the voltage.
Compare and contrast the
measured and calculated
voltages.
V

 There is one final
measurement to complete
this portion of the exercise.
Insert the VOM as
indicated.
 Recall the 3 voltages
measured previously;
across R1, R2 and R3, and
across R4.
 Add these three voltages
together and then compare
and contrast the result
with the total voltage just
measured.
V

 What you observed was:
 The sum of the individual currents was equal to the
total current flowing through the circuit.
 The sum of the voltage drops was equal to the total
voltage across the circuit.
 This is Kirchhoff’s Law and is very useful in
the study of electronic circuit.
 You also noted that Ohm’s Law applied
throughout the circuit.

The Capacitor
 Capacitance defined
 Physical construction
 Types
 How construction
affects values
 Power ratings
 Capacitor performance
with AC and DC
currents
 Capacitance values
 Numbering system
 Capacitors in circuits
 Series
 Parallel
 Mixed

The Capacitor (Defined)
A device that stores energy in
electric field.
Two conductive plates
separated by a non
conductive material.
Electrons accumulate on one
plate forcing electrons away
from the other plate leaving a
net positive charge.
Think of a capacitor as very
small, temporary storage
battery.

The Capacitor (Physical Construction)
 Capacitors are rated by:
 Amount of charge that
can be held.
 The voltage handling
capabilities.
 Insulating material
between plates.

The Capacitor (Ability to Hold a
Charge)
 Ability to hold a charge
depends on:
 Conductive plate surface
area.
 Space between plates.
 Material between plates.

Charging a Capacitor
In the following activityyou will
charge a capacitor by connecting
a power source (9 volt battery) to
a capacitor.
You will be using an electrolytic
capacitor, a capacitor that uses
polaritysensitive insulating
material between the conductive
plates to increase charge
capabilityin a small physical
package.
Notice the component has
polarity identification + or -.
+

 Touch the two leads of the capacitor together.
 This short circuits the capacitor to make sure there
is no residual charge left in the capacitor.
 Using your VOM, measure the voltageacross the
leads of the capacitor

Wire up the circuit illustrated
and charge the capacitor.
Power will only have to be
applied for a moment to fully
charge the capacitor.
Quickly remove the capacitor
from the circuit and touch the
VOM probes to the capacitor
leads to measure the voltage.
Carefully observe the voltage
reading over time until the
voltage is at a very low level
(down to zero volts).
+

The Capacitor (Behavior in DC)
 When exposed to DC, the capacitor charges and
holds the charge as long as the DC voltage is
applied.
 The capacitor essentially blocks DC voltage from
passing through.

The Capacitor (Behavior in AC)
 When AC current is applied, during one half of the
cycle the capacitor accepts a charge in one
direction.
 During the next half of the cycle, the capacitor is
discharges then recharged in the reverse direction.
 During the next half cycle the pattern reverses.
 Essentially, it appears that AC current passes
through a capacitor

The Capacitor (Behavior)
 A capacitor blocks the passage of DC
 A capacitor passes AC

The Capacitor (Capacitance Value)
 The unit of capacitance is the farad.
 A single farad is a huge amount of capacitance.
 Most electronic devices use capacitors that have a
very tiny fraction of a farad.
 Common capacitance ranges are:
 Micro - 10-6
 Nano - 10-9
 Pico - 10-12

p
n

The Capacitor (Capacitance Value)
 Capacitor identification
depends on the capacitor
type.
 Could be color bands, dots,
or numbers.
 Wise to keep capacitors
organized and identified to
prevent a lot of work trying
to re-identify the values.

Capacitors in Circuits
 Two physical factors
affect capacitance
values.
 Plate spacing
 Plate surface area
 In series, plates are
far apart making
capacitance less
21
21
CC
CC

+
-
Charged plates
far apart

Capacitors in Circuits
 In parallel, the surface
area of the plates add
up to be greater, and
close together.
 This makes the
capacitance more the
Capacitor
21 CC 
+
-

The Inductor
 Inductance defined
 Physical construction
 How construction
affects values
 Inductor performance
with AC and DC
currents

The Inductor
 There are two fundamental principles of
electronics:
1. Moving electrons create a magnetic field.
2. Moving or changing magnetic fields cause
electrons to move.
 An inductor is a coil of wire through which
electrons move, and energy is stored in the
resulting magnetic field.

The Inductor
 Like capacitors,
inductors temporarily
store energy.
 Unlike capacitors:
 Inductors store energy
in a magnetic field, not
an electric field.
 When the source of
electrons is removed,
the magnetic field
collapses immediately.

The Inductor
 Inductors are simply
coils of wire.
 Can be air wound
(nothing in the middle
of the coil)
 Can be wound around
a permeable material
(material that
concentrates magnetic
fields)
 Can be wound around
a circular form (toroid)

The Inductor
 Inductance is measured in Henry(s).
 A Henry is a measure of the intensity of the magnetic
field that is produced.
 Typical inductor valuesused in electronics are in the
range of milli Henry (1/1000) and micro Henry
(1/1,000,000)

The Inductor
 The amount of
inductance is
influenced by a
number of factors:
 Number of coil turns.
 Diameter of coil.
 Spacing between
turns.
 Size of the wire used.
 Type of material
inside the coil.

Inductor Performance With
DC Currents
When DC current is applied to an inductor, the wire in the
inductor momentarily appears as a short circuit and
maximum current flows.
As the magnetic field builds (changes) there is a tendency
for the current flow to slow down (due to an opposition
cause the the changing magnetic field).
Finally, the magnetic field is at its maximum and the
current flows to maintain the field.
As soon as the current source is removed, the magnetic
field begins to collapse and creates a rush of current in the
other direction, sometimes at very high voltages.

Inductor Performance With AC
Currents
When AC current is applied to an inductor, during
the first half of the cycle, the magnetic field builds
as if it were a DC voltage.
During the next half of the cycle, the current is
reversed and the magnetic field first has to
decrease the reverse polarity in step with the
changing current.
Depending on the value of inductance, these
forces can work against each other, making for a
less than simple situation.

The Inductor
 Because the magnetic
field surrounding an
inductor can cut
across another
inductor in close
proximity, the
changing magnetic
field in one can cause
current to flow in the
other … the basis of
transformers

The Diode
 The semi-conductor phenomena
 Diode performance with AC and DC currents
 Diode types
 Basic
 LED
 Zenier

The Diode (The semi-conductor
phenomena)
 Electrons in a metal form a “sea” of electrons
that are relatively fee to move about.
 Semiconducting materials like Silicon and
Germanium have fewer free electrons.
 Impurities added to semiconductor material can
either add free electrons or create an absence of
electrons (holes).

The Diode (The semi-conductor phenomena)
Consider the bar of silicon at the right.
One side of the bar is doped with negative material
(excess electrons). The cathode.
The other side is doped with positive material
(excess holes). The anode
In between is a no man’s land called the P-N
Junction.

phenomena)
 Consider now applying a negative voltage to the
anode and positive voltage to the cathode.
 This diode is reverse biased meaning no current
will flow.

phenomena)
 Consider now applying a positive voltage to the
anode and a negative voltage to the cathode.
 This diode is forward biased meaning current will
flow.

The Diode
 Set up the circuit
illustrated on the
proto board.
 Ensure to note the
cathode (banded end)
of the diode.
 Use a 330 ohm
resistor. The resistor
in the circuit is a
current limiting
resistor.
A
330

The Diode
 Set up the circuit
illustrated on the
proto board (reverse
the diode).
 Ensure to note the
cathode (banded
end) of the diode.
A

The Diode
 Build the illustrated
circuit.
drop across the diode
that is forward biased.
V

The Diode with AC Current
 If AC is applied to a diode:
 During one half of the cycle the diode is forward
biased and current flows.
 During the other half of the cycle, the diode is
reversed biased and current stops.
 This is the process of rectification, allowing
current to flow in only one direction.
 i.e., changing AC into DC

The Diode with AC Current
Input AC
Output
Pulsed DC
Diode
conducts
Diode off

The Light Emitting Diode
 In normal diodes, when electrons combine with
holes heat is produced.
 With some materials, when electrons combine
with holes, photons of light are emitted.
 LEDs are generally used as indicators though they
have the same properties as a regular diode.

The Light Emitting Diode
Build the illustrated
circuit on the proto
board.
The longer LED lead is
the anode (positiveend).
Then reverse the LED
and observe what
happens.
The current limiting
resistor not only limits
the current but also
controls LED brightness.
330

Zener Diode
A Zener diode is
designed through
appropriate doping so
that it conducts at a
predetermined reverse
voltage.
The diode begins to
conduct and then
maintains that
predetermined voltage
The over-voltageand
associated current must
be dissipated by the
diode as heat
9V 4.7V

The Transistor (Electronic Valves)
 How they works, an inside look
 Basic types
 NPN
 PNP
 The basic transistor circuits
 Switch
 Amplifier

The Transistor
base
collector
emitter
collector
collector
base

The Transistor
N P N
collector emitter
base e -e -
forward bias
conducting
e -

The Transistor
N P N
collector emitter
base e -e -
reverse bias
no-conducting

The Transistor
 There are two basic types of
transistors depending of the
arrangement of the material.
 PNP
 NPN
 An easy phrase to help
remember the appropriate
symbol is to look at the arrow.
 PNP – pointing in proudly.
 NPN – not pointing in.
 The only operational difference
is the source polarity.
PNP
NPN

The Transistor Switch
 During the next two
activities you will
build a transistor
switch and a transistor
amplifier.
 The pin out of the
2N3904 transistor is
indicated here.
C
B
E

 Build the circuit on the
proto board.
 Use hook up wire to
serve as “switches” to
connect the current to
the transistor base.
 What happens when
you first apply power
when the base is left
floating (not
connected)?
330
1000

Make the illustrated
adjustment to the
circuit.
Connect one end of
some hook-up wire to
the positive side of the 9
volt battery.
Touch the other end
(supply9 volts) to the
resistor in the base line
and observe what
happens.
330
1000

 Now replace the hook-
up wire connection with
a connection to a 1.5 volt
battery as shown.
 What happens when
+1.5 volts is applied to
the base?
 What happens when the
battery is reversed and –
1.5 volts is applied to the
base?
330
10001.5V
9V

The iot academy_embeddedsystems_training_basicelectronicspart1

The iot academy_embeddedsystems_training_basicelectronicspart1

Recommended

More Related Content

What's hot (20)

Similar to The iot academy_embeddedsystems_training_basicelectronicspart1 (20)

More from The IOT Academy (20)

Recently uploaded (20)

The iot academy_embeddedsystems_training_basicelectronicspart1