Real Time ECG and Saline Level Monitoring System Using Arduino UNO Processor

Asian Journal of Applied Science and Technology (AJAST)
Volume 1, Issue 2, Pages 160-164, March 2017
© 2017 AJAST All rights reserved. www.ajast.net
Page | 160
Real Time ECG and Saline Level Monitoring System Using Arduino UNO
Processor
P.Kalaivani1
, T.Thamaraiselvi2
, P.Sindhuja3
and G.Vegha4
1Assistant Professor, Department of Electronics and Communication Engineering, SNS College of Engineering, Coimbatore, India.
2UG Student, Department of Electronics and Communication Engineering, SNS College of Engineering, Coimbatore, India.
Article Received: 28 February 2017 Article Accepted: 16 March 2017 Article Published: 18 March 2017
1. INTRODUCTION
In many cases, Patient requires continuous monitoring and
essentially needs lengthy stay in hospitals which is again
becoming costly now days. Traditional monitoring system
allows continuous monitoring of vital parameters which
require the sensors to be connected to bedside machines or
PCs, and patient is essentially confined to bed.
However, today’s busy world and increase in sudden death
events motivates for a monitoring system that continuously
monitors remotely located patient. Depending on this factor
many researchers have developed patient monitoring system.
ECG Holter monitoring is the most widely used technique for
providing ambulatory cardiac monitoring for capturing
rhythm disturbances. A traditional Holter monitor can record
up to 24 hours of ECG signals and the recorded data is
subsequently retrieved and analyzed by a clinician.
Due to the short duration involved and the unknown context
within which ECG signal is captured; reliable interpretation
of the recorded data is always a challenge. Telemetry is
another way of monitoring remotely located patient.
However, current biomedical devices lack in the ability to
provide large-scale analysis, simulations and computations at
the patient’s location. Wireless Sensor Network is becoming a
promising technology for various applications. One of its
potential deployments is in the form of Wireless Biomedical
Sensor Network (WBSN) for measuring physiological
signals. Many ECG monitoring system are developed based
on WSN technology.
2. EXSITING WORKS
2.1.1 Application using mobile devices
In the last decade the healthcare monitoring systems have
drawn considerable attentions of the researchers. The prime
goal was to develop a reliable patient monitoring system so
that the healthcare professionals can monitor their patients,
who are either hospitalized or executing their normal daily life
activities. In this work we present a mobile device based
wireless healthcare monitoring system that can provide real
time online information about physiological conditions of a
patient. Our proposed system is designed to measure and
monitor important physiological data of a patient in order to
accurately describe the status of her/his health and fitness. In
addition the proposed system is able to send alarming
message about the patient’s critical health data by text
messages or by email reports. By using the information
contained in the text or e-mail message the healthcare
professional can provide necessary medical advising. The
system mainly consists of sensors, the data acquisition unit,
microcontroller (i.e., Arduino), and software (i.e.,
LabVIEW). The patient’s temperature, heart beat rate,
muscles, blood pressure, blood glucose level, and ECG data
are monitored, displayed, and stored by our system. To ensure
reliability and accuracy the proposed system has been field
tested. The test results show that our system is able to measure
the patient’s physiological data with a very high accuracy. A
Smartphone based health monitoring system has been
presented in this work. By using the system the healthcare
professionals can monitor, diagnose, and advice their patients
all the time. The physiological data are stored and published
online. Hence, the healthcare professional can monitor their
patients from a remote location at any time. Our system is
simple. It is just few wires connected to a small kit with a
Smartphone. The system is very power efficient. Only the
smartphone or the tablet needs to be charged enough to do the
test. It is easy to use, fast, accurate, high efficiency, and safe
(without any danger of electric shocks). In contrast to other
conventional medical equipment the system has the ability to
save data for future reference. Finally, the reliability and
validity of our system have been ensured via field tests. The
field tests show that our system can produce medical data that
ABSTRACT
The epidemic growth of wireless technology and mobile services in this epoch is creating a great impact on our life style. Some early efforts have been
taken to utilize these technologies in medical industry. In this field, ECG sensor based advanced wireless patient monitoring system concept is a new
innovative idea. This system aims to provide health care to the patient. We have sensed the patient’s ECG through 3 lead electrode system via
AD8232 which amplifies minor and small bio-signals to the arduino which processes them, along with saline level. Saline level is detected through IR
sensors. The output of the electrical pulse is shown with the serial monitor. The saline level is indicated by LCD. The major output ECG analog signal
is displayed on serial plotter. The outputs are displayed through mobile application.
Keywords: Arduino UNO, 3lead ECG clamp, AD8232, LCD display, IR sensor, Saline bottle, Bluetooth module and mobile phone.

Page | 161
are similar to those produced by the existing medical
equipment.
2.1.2 Wearable ECG Monitor
In this paper, a wearable medical device for
Electrocardiogram (ECG) and blood pressure monitoring is
presented. Its basis is a validated and certified existent
medical device. This device was evolved in order to allow
new physiological signal monitoring and real time assessment
of blood pressure levels by adding a photoplethismography
(PPG) probe and the incorporation of new algorithms in an
online interface. The device presents accuracies of 94.6% for
systolic blood pressure and 92.3% for systolic blood pressure
when compared with reference values obtained from a
commercial electronic Sphygmomanometer.
2.1.3 Saline Level Monitoring System
This paper proposes an automatic, low cost saline level
measurement system using microcontroller ATMEGA
328.The main building blocks of the proposed system are
microcontroller ATMEGA 328, Bluetooth module and IR
sensors. The system contains two LEDs. The status of the
saline can be given in two forms that are normal status and
warning status. When the saline level is normal, then green
LED blinks and when the saline level is below the critical
value then red LED will blink. When red LED blinks then
buzzer starts ringing and nurse will get notification through
mobile with the help of Bluetooth module. At present, there is
no such valid system for saline level monitoring.
Proposed system reduces efforts of nurses and it is very cost
effective as the same circuit which is used for the saline bottle
can be reused for another bottle. It can also be easily
implemented in rural hospitals. This paper proposes the
system which can automatically monitor the saline flow by
using microcontroller. The system is reliable, cost effective
and convenient for nurses. It can be reused for the next saline
bottle. It is beneficial for nurses as well as doctors at rural
hospitals. The system helps nurses to monitor the saline flow
from a distance. It is mainly advantageous at night timing as
there is no need for nurses to go to patient’s bed to check the
level of saline in the bottle.
3. PROPOSED WORK
In this proposed system, we have constrained the cost,
working space and simplified the gadgets to show the ECG
output. Serial plotter is used in displaying the analog signal
structure .The Arduino serial plotter function allows to
natively graph serial data from Arduino to PC in real time.
Serial plotter is an offline tool allowing to visualize data and
troubleshoot code offline without having to use third party
services like PLOTY. In our system there is a simplified
interface for two other parameters, saline level and pulse
detection. We use sensors for secondary parameter detection
and are directly interfaced with the Arduino processor. The
processor processes input data from the sensors and
concludes the final information using program code. It is
finally displayed on LCD. We have sensed the patient’s ECG
through 3 lead electrode system via AD8232 which amplifies
minor and small bio-signals to the Arduino which processes
them, along with saline level. Saline level is detected through
IR sensors. The output of the electrical pulse is shown with
the serial monitor. The saline level is indicated by LCD. The
major output ECG analog signal is displayed on serial plotter.
We also connect some external parameters (i.e.) pulses
calculated in beats per minutes.
3.1 Block Diagram
Block diagram of transmitter
3.1.1 Block 1 ECG Detection
Block 1 of transmitter
3.1.2 Block 2 Saline Detection
Block 2 of transmitter

Page | 162
3.2 Hardware
3.2.1 ECG Electrode
ECG electrode clamp
The heart has four chambers. The upper two chambers
(left/right atria) are entry-points into the heart, while the lower
two chambers (left/right ventricles) are contraction chambers
sending blood through the circulation. The circulation is split
into a “loop” through the lungs (pulmonary) and another
“loop” through the body (systemic).The cardiac cycle refers
to a complete heartbeat from its generation to the beginning of
the next beat, comprising several stages of filling and
emptying of the chambers. The frequency of the cardiac cycle
is reflected as heart rate (beats per minute, bpm).
3.2.2 Power Supply
Power supply adaptor
In the alternating current model, shown on the right side of
the figure, the line with the indications concerning the output
says: AC 12 V 500mA 6VA, that respectively represent:
alternating current, maximum output load and power,
expressed in VA. In some cases, in the place of the AC
abbreviation, the symbol “~” may be found, and it still means
“alternating current”. On the left, on the contrary, the direct
current model, in the line with the output values shows in an
equally clear way +5 V 2A.finally, in these power supplies,
the voltage polarity is always indicated on the output JACK;
in this case the graphics represented on the tag indicates that
the positive pole (+) is connected to the central part of the jack
while the negative pole (-) is connected to the external part.
We may still notice the presence of the “~” symbol on the tag,
but it is clearly referred to the power supply input that,
obviously, must be connected to the alternating current
network.
3.2.3 Arduino UNO R3
Arduino R3
Arduino/Genuine Uno is a microcontroller board based on the
ATmega328P. It has 14 digital input/output pins (of which 6
can be used as PWM outputs), 6 analog inputs, a 16 MHz
quartz crystal, a USB connection, a power jack, an ICSP
header and a reset button. It contains everything needed to
support the microcontroller; in the 14 digital pin we connect
pin 0 and 1 are used for transmitter and receiver pin of
Bluetooth. Pin 2-5 are used for LCD data configuration. Pin
6-8 are the high for parameter component this is acted as Vcc
of 5v.pin 10 and 11 are used for AD8232 lead off (LO-
) and
lead on (LO+
). Analog pin A0 is used for input from the
AD8232 output pin. Vcc and ground pin are connected
correspondingly. Every analog pin are get the input from the
sensors output.
3.2.4 AD8232
AD8232
The AD8232 may be an incorporated sign molding square to
ECG and other bio-potential estimation requisitions. It may
be planned will extract, amplify, Furthermore channel little
bio-potential.
This table measures electrical action of heart through set on
the skin. Interfacing this table for Arduino we get ECG chart
through preparing IDE window. We might utilize the cathode
jack or disaster will be imminent pin gaps for electrodes.
Associate relating cathode pads over skin et cetera give
acceptable 3. 3V.
What's more GND force supply from the Arduino board, the
SDN (shutdown) pin will be not associated with any apiece.
Yield from those breakout table will be made on Arduino’s
A0 (Analog enter 0) pin. Will identify those heads off
circumstances LO– and LO+ are associated with Arduino
advanced pin D11 and D10 separately.

Page | 163
3.2.5 Pulse Sensor
Pulse sensor
The Pulse Sensor Amped is a plug-and-play heart-rate sensor
for Arduino. It can be used by students, artists, athletes,
makers, and game & mobile developers who want to easily
incorporate live heart-rate data into their projects. It
essentially combines a simple optical heart rate sensor with
amplification and noise cancellation circuitry making it fast
and easy to get reliable pulse readings. Also, it sips power
with just 4mA current draw at 5V so it’s great for mobile
applications.
Pulse Sensor Amped is a plug-and-play heart-rate sensor for
Arduino and Arduino compatibles. It has 3 wires. provide
3.3V or 5V and GND for red and black pins. Purple color.
3.2.6 IR Sensor
An infrared sensor will be an electronic device that emits in
place will feeling exactly viewpoints of the surroundings. An
IR sensor might measure the high temperature from claiming
an article and also detects the movement. These sorts of
sensors measures only infrared radiation, as opposed emitting
it that is known as an indifferent IR sensor. Here sensor out
pin may be associated with the Arduino analog pin A1.
3.2.7 Bluetooth Module
It is a wireless technology standard for exchanging data over
short distances (using short-wavelength UHF radio waves in
the ISM band from 2.4 to 2.485 GHz) from fixed and mobile
devices, and building personal area networks (PANs). Range
is approximately 10 Meters (30 feet). BC417 2.4 GHz
Bluetooth Radio chip. KEY: If brought HIGH before power
is applied, forces AT Command Setup Mode. LED blinks
slowly (2 seconds) VCC: +5 Power GND: System / Arduino
Ground TXD: Transmit Serial Data from HC-05 to Arduino
Serial Receive. NOTE: 3.3V HIGH level: OK for Arduino
RXD: Receive Serial Data from Arduino Serial Transmit
.STATE: Tells if connected or not.
4. SOFTWARE
4.1 ARDUINO-1.8.1-R3-WINDOWS
An IDE for the Arduino microcontroller. Arduino is a free
software electronics prototyping platform based on flexible,
easy-to-use hardware and software. It's intended for artists,
designers, hobbyists, and anyone interested in creating
interactive objects or environments. This IDE allows for
program writing, code verification, compiling, and uploading
to the Arduino development board. Libraries and example
code will also be installed. The Arduino Software (IDE) on
computer, according to its operating system.
Windows, Mac OS x10.1, Linux 32 bits, Linux 64 bits,
Linux ARM. The Arduino Serial Plotter function has been
added to the Arduino IDE, allowing you to natively graph
serial data from your Arduino to your computer in real time. If
you’re tired of seeing your Arduino’s analog sensor input data
pour onto your screen like The Matrix, this looks like a
prettier way to visualize what’s going on. The Serial plotter is
an offline tool allowing you to visualize data and troubleshoot
your code offline without having to use third parts services
like Processing or Plotly. Since there is no official
documentation on the Arduino website regarding the use &
functionality of the Serial Plotter, I decided to documents its
uses and features.
4.2 Blue Terminal
Blue Terminal is a serial emulator program for Windows
only, and is customized to work with the Bluegiga range of
bluetooth modules. Blue Terminal is a serial emulator
program for Windows only, and is customized to work with
the Bluegiga range of bluetooth modules. Blue Terminal is
designed to build on previous terminal emulators, such as
Telix, Windows3 Terminal, Hyper terminal and Putty.
5. RESULTS AND DISCUSSION
5.1 Result
The electrical pulses and saline levels are the minor
parameters indicated through LCD and the major ECG is
shown through serial plotter, all the three parameters which
are vitally important in screening a cardio patient are
compactly displayed in one place making the doctor’s work
hazel free.
5.2 Output
Internal circuitry
Electrodes are fixed on the patient’s right wrist, left wrist and
right ankle. Then the sensors start to detect the patient’s
pulses continuously. Now we have sensed the patient’s ECG
through 3 lead electrode system, sending them directly to
AD8232 which amplifies minor and small bio-signals to the
Arduino which processes them and sends the processed data
to the Arduino program.
In this picture, the displayed serial monitor continuously lists
the number of signal sensed from real time pulse sensing.

Page | 164
Program interface
The sensed continuous ECG signal from the sensor is sent
through the AD8232 for amplification and the amplified real
time signals are plotted through the feature of the Arduino
processor called serial plotter. The Arduino serial plotter
function allows to natively graph serial data from Arduino to
PC in real time. Serial plotter is an offline tool allowing to
visualize data and troubleshoot code offline without having to
use third party services. Electrocardiography is the process of
recording the electrical activity of the heart over a period of
time using electrodes placed on the skin. These electrodes
detect the tiny electrical changes on the skin that arise from
the heart muscle's electro physiologic pattern
of depolarizing and repolarizing during each heartbeat. It is a
very commonly performed cardiology test.
Saline level interface
A separate structure consisting of saline bottle, elastic band,
IR sensor makes up the secondary parameter device that
detects and displays the saline level. The output is displayed
on the LCD.
The IR sensor sensing the level of the saline liquid is directly
connected to the Arduino UNO processor. Based upon the
processed real time data, software is written for the Arduino
to indicate low and high levels of saline as output.
In the above picture the result displayed is the level of saline
in the bottle indicated by detection as low.
6. CONCLUSION
With this proposed method, the monitoring of ECG signals
can be done easily with the further locating the doctor. By
means of compressing the real-time signal the rate of
compressing will be increased with high accuracy and more
data storage.
7. FUTURE WORK
Compressive sensing technique to be further proceed. Along
with ECG other signals can be transmitter for early diagnosis.
REFERENCES
[1] Allada Tirupathi Rao, M.Gopi, M.V.S.S.Prasad, “Real
Time ECG Signal Transmission for Remote Monitoring”,
ISSN: 2321-9939.
[2] Prerana N Gawale, A.N.Cheeran, Nidhi G Sharma,
“Android Application for Ambulant ECG Monitoring”,
International Journal of Advanced Research in Computer
and Communication Engineering, Vol. 3, Issue 5, May 2014.
[3] Onder Yakut, Serdar Solak, Emine Dogru Bolat,
“Implementation of a Web-Based Wireless ECG Measuring
and Recording System”, International Journal of Electrical,
Computer, Energetic, Electronic and Communication
Engineering, Vo.9, No.10, 2015.
[4] Kalaivani, P., G. Sathya Nikitha S Paulin, Boselin
Prabhu.S.R., Sophia.S, “Performance Improvement of
Distributed Island Multicasting with Overlay Data
Distribution”, Australian Journal of Basic and Applied
Sciences, 9(36) December 2015, Pages 221-228.
[5] Kalaivani, P., G. Sathya and N. Senthilnathan, 2014.
“Dynamic Data Routing in MANET using position based
opportunistic Routing Protocol”, International Journal of
research in computer Applications & Robotics (IJRCAR), 2:
12.
[6] Kalaivani, P., G. Sathya, N. Senthilnathan, “QoS
Parameters Estimation in MANET Using Position Based
Opportunistic Routing Protocol”, American Journal of
Computer Science and Engineering Survey, ISSN
2349-7238.
[7] Sathya, G., P. Kalaivani, N. Senthilnathan, 2015.
“Balancing the Energy Consumption and Data Integrity in
MANET”, International Journal of Chemical Sciences and
Research, 3(2).
[8] Addison PS (2005), “Wavelet transforms and the ECG: a
review”, PhysiolMeas 26(5):R155.
[9] Alemdar H, Ersoy C (2010), “Wireless sensor networks
for healthcare: a survey”, Comput Netw., 54(15):2688–2710.
[10] R.Vasuki et al., “An portable monitoring device of
measuring drips rate by using an Intravenous (IV) set”,
International Journal of Biotechnology Trends and
Technology, Vol. 1, Issue 3, No.4 2011.
[11] C.C.Gavimath et al., “Design and Development of
versatile saline flow rate measuring system and GSM based
remote monitoring device”, International Journal of
Pharmaceutical Applications, ISSN 0976-2639.
[12] R.Aravind, Syed Mustak Ahmed, “Design of family
health monitoring system using wireless communication”,
International Journal of Advanced Research in Computer
and Communication Engineering, Vol. 2, Issue 9, September
2013.

Real Time ECG and Saline Level Monitoring System Using Arduino UNO Processor

Recommended

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Real Time ECG and Saline Level Monitoring System Using Arduino UNO Processor (20)

More from Associate Professor in VSB Coimbatore (20)

Recently uploaded (20)

Real Time ECG and Saline Level Monitoring System Using Arduino UNO Processor