Evolution of Structure of Some Binary Group-Based N-Bit Compartor, N-To-2N Decoder by Reversible Technique

International Journal of VLSI design & Communication Systems (VLSICS) Vol.5, No.5, October 2014
EVOLUTION OF STRUCTURE OF SOME BINARY
GROUP-BASED N-BIT COMPARATOR, N-TO-2N
DECODER BY REVERSIBLE TECHNIQUE
Neeraj Kumar Misra1, Subodh Wairya2 and Vinod Kumar Singh3
Department of Electronics Engineering,
Institute of Engineering and Technology, Lucknow, India
ABSTRACT
Reversible logic has attracted substantial interest due to its low power consumption which is the main
concern of low power VLSI systems. In this paper, a novel 4x4 reversible gate called inventive gate has
been introduced and using this gate 1-bit, 2-bit, 8-bit, 32-bit and n-bit group-based reversible comparator
have been constructed with low value of reversible parameters. The MOS transistor realizations of 1-bit, 2-
bit, and 8-bit of reversible comparator are also presented and finding power, delay and power delay
product (PDP) with appropriate aspect ratio W/L. Novel inventive gate has the ability to use as an n-to-2n
decoder. Different novel reversible circuit design style is compared with the existing ones. The relative
results shows that the novel reversible gate wide utility, group-based reversible comparator outperforms
the present style in terms of number of gates, garbage outputs and constant input.
KEYWORDS
Reversible Logic, Inventive Gate, Garbage Output, Constant input, Full subtractor, n-bit reversible
comparator, Reversible decoder etc.
1. INTRODUCTION
In low power VLSI systems planning of power is one of important aspects. According to
Landauer [1] in 1960 demonstrate that single bit of information loss generate at least KT ln2 J/K
of energy where K is the Boltzmann constant (1.38x10-23 J/K) and T is the absolute temperature.
Reversible circuits are totally different from irreversible circuits. In reversible logic no bits is loss
the circuit that doesn't loss information is reversible.
C.H Bennet [2] in 1973 proves that KT ln2 joule of energy wouldn't be dissipated if the reversible
circuit consist of reversible gates only. Thus reversible logic operations do not loss information
and dissipate less heat also as power. Thus reversible logic is probably going to be in demand in
high speed power aware circuits. A reversible circuit planning has following important attributes
Garbage output, number of reversible gates, constant input all should be minimum for efficient
reversible circuits.
Comparator has wide applications in Analog and digital circuits, Analog to digital (A/D)
converters, Level shifter, and communication system etc. It compares the 2-number of several
DOI : 10.5121/vlsic.2014.5502 9

bits. In this paper introduce group-based n-bit reversible comparator [6,9,11] and n-to-2n
reversible decoder with low value of reversible parameters with the help of lemmas.
This paper is organised with the following sections: Section 2 and 3 discuss basic definition of
reversible logic and parameter optimization taken; Section 4 discuss the past work; Section 5
discuss the utility and design issue of novel 4x4 inventive gate; Section 6 Planning of low value
style reversible comparator subsection of 6.1 introduce novel 1-bit comparator cell, subsection
6.2 and 6.3 is novel match, larger and smaller comparator cell design; Subsection 6.4, 6.5, 6.6.
6.7 for 2-bit, 8-bit, 32-bit and n- bit group-based reversible comparator design respectively;
Section 7 Implement all comparator cell in MOS transistor with minimum MOS transistor count.
Section 8 categories as simulation result of comparator. Finally, the paper is concluded and future
work with Section 9.
10
2. BASIC DEFINITIONS OF REVERSIBLE LOGIC
In this section, we introduce the essential definitions of reversible logic which are relevant with
this research work.
Definition 2.1 A reversible gate is a Z - input and Z - output that generate a unique output pattern
for each possible input pattern.
Definition 2.2 In Reversible logic output and input is equal in number. Unwanted output is called
garbage output it should be minimum as possible and fan-out is not allowed.
3. PARAMETER OPTIMIZED FOR DESIGNING EFFICIENT REVERSIBLE
CIRCUITS
The main challenge of designing efficient reversible circuits is to optimize the different reversible
parameters which result the circuit design is costly. The most necessary parameters which have
dominant in efficient reversible logic circuits are:
3.1 Garbage output
Unutilized or unwanted output of reversible circuit is called garbage output. It should be kept
minimum as possible.
3.2 Constant Input
Constant bits are additional inputs that are not part of the original specification. These bits are
added in hopes to reduce the circuit complexity or realize a reversible function. They come in the
form of a constant logic 1 or 0. It is ideal to keep in minimal.
3.3 Few Reversible gates utilized
In this subsection, we present few reversible gates that are used to design for planning different
types of reversible circuit. First TR (3×3) utilize input (A, B, C) and carry output (P=A,
Q=A⊗B, R=AB’⊗C, Second BME gate(4X4) utilize input (A, B, C, D) and carry output (P=A,

Q=AB⊗C, R=AD⊗C) and S=A’B⊗C⊗D, Third Feynman gate (FG) 2x2 utilize input (A, B )
and carry output (P=A, Q=A⊗B), Fourth Peres gate (PG) 3x3 utilize input (A, B, C) and carry
output (P=A, Q=A⊗B, R=AB⊗C)
11
3.4 Flexibility
Flexibility refers to the universality of reversible logic gate in realizing more logical function.
4. PAST WORK
In 2010, Himanshu thapliyal et.al [17] design a reversible 8-bit and 64-bit tree-based comparator
using TR Gate that has the latency of O(log2(n)).But this approach is not suitable for low value
of reversible parameter and not extended for n-bit reversible comparator. Furthermore another
comparator design by Rangaraju H Ga [7, 8] in 2011 has shows that design has input circuit as
first stage and 1-Bit comparator cell as second stage and so on. This idea is extend for n-bit
reversible comparator design but it is not sufficient to optimizing the reversible parameter. In
2011, Nagamani et.al. [21] Design a reversible 1-bit reversible comparator with low value of
reversible parameter but this idea is not extended for n-bit comparator.
In 2013, Ri-gui Zhou et.al. [5] design a novel 4-bit reversible comparator. It is mentioned in
paper further possibilities of reducing the number of reversible gates, constant input and garbage
output in the area of reversible comparator design. They proposed new gate and using this gate
form various gate AND, OR, XNOR, NOT, FA, FS but not form gate NAND, NOR. For
increasing order of comparator, gate increase in higher order and complexity of design increases
and also garbage outputs means performance of comparator degrade.
In 2013, Hafiz Md. Hasan babu et.al. [4] design compact n-bit reversible comparator. Its design is
efficient because it reduce complexity of design. Approach is sufficient and proposed various
theorem and lemma for calculating n-bit reversible parameter number of gate, total delay, power.
They proposed two new gate BJS and HLN. These gate form OR, AND, XOR and NOT
Operation but not form FA, FS, NAND and NOR Operation. For showing expertise of reversible
gate we work on this and proposed Universal gate called Inventive Gate. It’s performing all
logical operation NAND, NOR, AND, OR, HA, HS, FA and FS and also form efficient group-based
n-bit reversible comparator and n-to-2n bit decoder with low value of reversible parameters.
5. UTILITY AND DESIGN ISSUES OF FRESHLY PROJECTED 4X4
INVENTIVE GATE
In this section, a new 4 x 4 reversible gates called Inventive gate, is proposed. The block
representation of inventive gate is shown in Figure 1.The corresponding truth table shown in
Table 1. And subsequent four logical configuration is presented P=(a⊗b⊗c),
Q=[(a⊗b)⊗d]c+b(a⊗d), R=(c'b'+d)a'+bc and S=b’d’(a+c)+d(b+a’c’) of inventive gate. It is
shown from the truth table that the attainable output pattern can be uniquely determined.

12
Figure 1. Block representation of Reversible 4 × 4 Inventive Gate
Table 1 Reversibility of the novel Inventive gate
INPUT OUTPUT
d c b a P Q R S
0 0 0 0 0 0 1 0
0 0 0 1 1 0 0 1
0 0 1 0 1 0 1 0
0 0 1 1 0 1 0 0
0 1 0 0 1 0 1 1
0 1 0 1 0 1 0 1
0 1 1 0 0 1 1 0
0 1 1 1 1 1 1 0
1 0 0 0 0 0 1 1
1 0 0 1 1 0 0 0
1 0 1 0 1 1 0 1
1 0 1 1 0 0 0 1
1 1 0 0 1 1 0 0
1 1 0 1 0 0 0 0
1 1 1 0 0 1 1 1
1 1 1 1 1 1 1 1
5.1 Utility-1 of Inventive gate
The proposed Inventive gate can implement all Boolean expression and it is a universal gate. In
this paper, Inventive gate is used to design the n-to-2n decoder (Shown in section 5.2) and 1-bit
comparator (Shown in section 6.1). The classical operations realized using Inventive gate is
shown in Fig a, b, c, d, e, f, g and h.
Fig a. AND, NAND gates Implementation Fig b. XOR, AND, NOT, OR gates Implementation

13
Fig c. NOR gate Implementation Fig d. XNOR, AND gates Implementation
Fig e. Half adder Implementation Fig f. Half substractor Implementation
Fig g. Full adder Implementation Fig h. Full substractor Implementation
5.2. Utility-2 of Reversible inventive gate as Reversible n-to-2n decoder
In this section we show the utility-2 of Inventive gate. It performs the operation of Reversible 2-
to-22 decoder it consists of two approaches named approach - 1 and approach - 2. Approach- 1 of
2-to-22 decoder generate 2 garbage output and number of gate count is 5. Whereas the Approach -
2 generate 2 garbage output but reduces number of gate count is 4 as shown in Figure 2 (b). And
also implement of 3-to-23 decoder (Approach 2) generate 3 garbage output and number of gate
count 7 as shown in Figure 4 .Decoder [3,11,14] are widely used in applications like information
multiplexing, 7 segment show and memory addressing.
5.2.1 Reversible 2-to-22 decoder and 3-to-23 decoder
Planning of Reversible 2-to-22 decoder is shown in Figure 2(b). It consists of (1 inventive gate+
2NOT+ 1 FG+ 1TG) types of gates. It has two input marked a, b apply to inventive gate and
Feynman gate (FG) respectively obtained output is passed to TG and gives output is (ab) other
output of decoder is (a' b), (a b') and (a' b'). Completed cell of 2-to-22 decoder are named as
I_F_T decoder cell. These cell are utilize for designing 3-to-23 decoder as shown in Figure 4.
Lemma 5.2.1.1 An n-to-2n reversible decoder (Approach 1) may be accomplished by a minimum
of 2n + 2 reversible gates, where n is that the range of bits and n 2
Proof. We ensure the above statement by mathematical induction.

International Journal of VLSI design Communication Systems (VLSICS) Vol.5, No.5, October 2014
For 2-to-22 decoder n = 2 decoder (Approach- 1) is made exploitation (1 inventive gate+ 2NOT+
2 FG+ 1TG) types of gates needs a minimum of 6 (2n + 2) reversible gate. Therefore the
statement assert for the base value of n=2.
Accept the statement for n = y thus a y-to-2y decoder may be realized by a minimum of 2y + 2
reversible gates.
For (y+1)-to-2(y+1) decoder is made exploitation y- to -2y decoder and 2y FRG Gate. So the Total
number of gates needed to construct a (y+1) - to- 2(y+1) decoder is a minimum of
2y+ 2+2y = 2y+1+2
14
So the statement hold for n = y+1
Lemma 5.2.1.2 An n-to-2n reversible decoder (Approach - 2) may be accomplished by a
minimum of 2n+1 reversible gates, where n is that the range of bits and n2
For 2-to-22 decoder n = 2 decoder (Approach -2) is made exploitation (1 inventive gate+
2NOT+1 FG+1TG) type of gates needs a minimum of 5 (2n+1) reversible gate. Therefore the
statement assert for the base value of n=2.
Accept the statement for n = y thus a y-to-2y decoder may be realized by a minimum of 2y+1
reversible gate.
For (y+1)-to-2(y+1) decoder is made exploitation y-to-2y decoder and 2y FRG Gate. So the total
range of gates needed to construct a (y+1)-to-2(y+1) decoder is a minimum of.
2y+1+2y = 2y+1+1
So the statement hold for n = y+1 and more powerful than approach 1 because it less number of
gate count.
Lemma 5.2.1.3 An n-to-2n reversible decoder (Approach -2) may be accomplished by a
minimum of n garbage output, where n is that the range of bits and n 2
For 2-to-22 decoder has garbage output 2 (n) for the base value of n = 2. For higher order decoder
3-to-23 garbage output 3 (n) for n=3
Accept the statement for n = k thus a k: 2k decoder may be realized by a minimum of k garbage
output.

15
a. Approach- 1
b. Approach – 2
Figure 2. Two approaches of the Novel 2- to- 22 decoder
Figure 3. Approach- 2 of proposed reversible 2-to-22 decoder Cell

16
c. Approach- 1
d. Approach- 2
Figure 4. Two Approaches of the proposed 3 -to- 23 decoder
Figure 5. Approach - 2 of proposed reversible n -to- 2n decoder
6. NOVEL DESIGN OF GROUP-BASED REVERSIBLE N-BIT BINARY
COMPARATOR
Following section we have to project a low value of group-based reversible n-bit comparator.
6.1 Novel 1-bit reversible comparator cell design
Novel 1-bit group-based reversible comparator structure uses 3 gates of 2 types (1 inventive+ 2
NOT) .It is true that ab’ for (ab), a’b for (ab) and a⊙b for (a=b). The proposed architecture has

constant input of 2, Garbage output of 1 and number of gate count 3. The structure of 1-bit
comparator modelled as I_N Comparator cell. As shown in Figure 6 (a)
17
6.2 Novel 1- bit Match and larger reversible comparator cell design
Novel 1-bit match and larger comparator structure use 4 Gate of 4 types (1 TR+ 1 NOT+1
BME+1 FG) .First reversible TR gate use (n- 1)th bits of two logic input a and b it produce two
significant output (a⊙b) and ab’ first output is not utilize is called garbage output. Two more nth
bit input Pn and Qn of previous comparator result is applied to reversible BME Gate it produce
two significant output Qn-1 = Qn (a⊙b) and Qn (ab’) only Qn-1 output save and other output Qn (a
b’) is applied to another reversible Feynman gate (FG) and another nth bit input Pn input is
selecting give one significance output Pn-1 = Qn (a b’) ⨂ Pn these two output Pn-1 and Qn-1 is
utilizing further for designing lesser logic comparator design. The proposed architecture has
constant input of 2, garbage output of 4 and number of gate count 4 (1+1+1+1). The structure of
Larger and Match design modelled as TR_BME_FG Comparator cell. As shown in Figure 6 (b)
6.3 Novel 1-bit smaller reversible comparator cell design
Novel single bit smaller reversible comparator structure use 4 gate of 2 type (3 FG + 1
NOT).These structure utilize two input P and Q and give two significant output P and (P⨂Q)
second output (P ⨂ Q) is passed to NOT gate gives (P ⊙ Q) other output is P and Q for match
operation use (P), Larger operation (Q) and lesser operation (P⊙Q). The novel design has
constant input of 1, Garbage output of 0 and Number of gate count 3 (1+1+1). The structure of
lesser cell modelled as F_F Comparator cell. As shown in Figure 6 (c)
6.4 Novel Efficient 2-bit reversible comparator design
Design methodology of 2-bit group- based comparator cell used three cell pervious section
named I_N Comparator cell, TR_BME_FG Comparator cell and F_F Comparator cell these cell
are connect and gives significant output P,Q and R for Match, Smaller and Larger logic. The
novel design is shown in Figure. 6 (d)
a

18
b
c
d
Figure 6. Reversible group-based 2-bit comparator design
a. Reversible 1-bit Comparator.
b. Match and Larger Cell design using TR_BME_FG Cell.
c. Smaller Comparator Cell design using F_F Cell.
d. Reversible 2-bit Comparator.
6.5 Novel architecture of Reversible 8-bit group-based Comparator
Following the extremely comparable analogous approach kept in mind then we are design
structure of 8-bit group-based Comparator module. The main projected structure for the 8-bit
Comparator is anticipated in Figure 7. The proposed architecture has constant input of 17

(1×2+2×7+1), Garbage output of 29 (1+ 4×7+ 1×0) and Number of gate count 34
(1×3+4×7+1×3)
19
1
0
b7
Q 2
Q 2
Q 2
a 7
b 8
a8
a 6
b 6
a5
b 5
a 4
b4 a 3
b 3
a 2
b 2
a 1
b 1
0
P = E
Q = G
PoQ= L
P1
Q 1
P 8
Q 8
P 7
Q 7
P6
Q 6
P 5
Q 5
P4
Q 4
P3
Q 3
P 2
P 1
Q 1
Q 2
Figure 7. Novel architecture of Reversible 8-bit Comparator
6.6 Novel architecture of Reversible 32-bit Group-based Comparator structure.
For the implementation methodology of 32-bit group-based comparator design use (1 I_N
Comparator Cell+ 31 TR_BME_FG Comparator cell+1 F_F Comparator cell) .The main
projected structure for the 32-bit binary group-based comparator cell is anticipated in Figure 8.

The proposed architecture has constant input of 65 (1×2+ 2×31+ 1×1), Garbage output of 125
(1×1+ 4×31+ 1×0) and Number of gate count 33 (1+ 31+ 1)
20
1
0
PoQ= L
0
P= E
Q = G
P1
Q1
Figure 8. Novel architecture of group-based reversible 32- bit Comparator

21
6.7 Novel architecture of Reversible n- bit group- based Comparator structure
Following the extremely comparable analogous approach we are proposing n- bit group-based
comparator structure. First idea is replenishment to the main projected structure for the n-bit
group-based comparator structure is anticipated in Figure 9. For designing 32-bit tree comparator
cell consist of nth single bit to I_N comparator cell and (n-1), (n-2), (n-3)………..(n-31)th single
bit apply to TR_BME_FG Comparator cell where n is 32 for 32-bit comparator. This concept is
apply for n-bit group-based comparator it consist of nth single bit to I_N comparator cell and (n-
1), (n-2), (n-3)………..(n-31)………….(n-y)th single bit apply to TR_BME_FG comparator cell
where y=(n-1)
Figure 9. Novel n- bit group- based reversible Comparator
The steps to style a n-bit group-based comparator are describe in Algorithm 1.
Algorithm1. Group- based n-bit Reversible Comparator
(1) Pick up I_N Comparator cell and acquire input an and bn
(2) Pick up TR_BME_FG Comparator cell and takes (n- 1)th bits of 2-binary variety an-1 and bn-1
and 2 additional input Pn and Qn from previous comparison result.
(3) TR_BME_FG Comparator cell 2-output Pn-1 and Qn-1 that indicates whether the given
binary number are equal to one another or larger.
(4) Pick up F_F Comparator cell and takes input P, Q it offers output P (For Equal) L(Less) =
P⊙Q and G (For Greater).
Lemma 6.7.1 An n-bit group-based reversible comparator may be accomplished by a 6+4 (n-1)
number of gate, 1+4 (n-1) garbage output, where n is the range of bits and n 2
Proof: We ensure the above statement by mathematical induction.
An n-bit reversible comparator has number of gate 6+ 4 (n-1). For realisation of 2-bit and 8-bit
reversible comparator setting n=2, 8 alternatively gives 10 and 34 number of gate.

22
An n-bit reversible comparator has garbage output 1+ 4 (n-1) .For realisation of 2-bit and 8-bit
reversible comparator setting n=2, 8 alternatively give 5 and 29 number of garbage output.
Lemma 6.7.2 An n-bit group-based reversible comparator requires (85.816n – 78.989) μW
power, where n is the range of bits and n 2
Proof: Novel n-bit group-based comparator uses I_N Comparator cell, (n– 1) TR_BME_FG
Comparator cell and one F_F Comparator cell. Total power relished by following specified
equation
Total Power (P) = PI_N Cell + (n-1) PTRE_BME_FG Cell + PF_F Cell
All Comparator cell implement in MOS transistor and finding power using T-Spice tool for 90nm
technology node. We have computed the power of I_N comparator cell, TRE_BME_FG
Comparator cell and F_F Comparator cell that are 3.358, 85.816 and 3.470 μW respectively. Now
the total power (P) of an n-bit group-based comparator as below
P= {3.35 + (n – 1) 85.81+ 3.4702} μW
= (3.35 +85.81n – 85.81 + 3.4702) μW
= (85.81n – 78.98) μW
Lemma 6.7.3 An n-bit group-based reversible comparator may be accomplished by a Timing
delay (T) of (115.010 n – 100.854) ns, where n is the range of bits and n2
Proof: Novel n-bit group-based Comparator uses I_N Comparator cell, (n– 1) TR_BME_FG
Comparator cell and one F_F Comparator cell .Total delay (T) relished by following specified
equation
Total delay (T) = TI_N Cell+ (n – 1) TTRE_BME_FG Cell + TF_F Cell
All Comparator cell implement in MOS transistor and finding delay using T-Spice tool for 90nm
technology node. We have computed the power of I_N comparator cell, TRE_BME_FG
Comparator cell and F_F Comparator cell that are 12.51, 115.010 and 1.608 ns respectively. Now
the delay of an n-bit group-based comparator as below
T= {12.51+ (n –1) 115.010 + 1.608} ns
= (12.51+ 115.010 n – 115.010 + 1.608) ns
= (115.010 n – 100.854) ns

Algorithm- 2 Reversible group-based n-bit comparator
*Design a n-bit reversible binary comparator when (n 2) with minimum number of gates and
Else Yn[1] = Pyn = 1
End if
Step 2. For TR_BME_FG and F_F Comparator cell, Level of input and output are considered
23
garbage output.
Begin
Step 1. Pick up I_N comparator cell and pick input Xn and output Yn for two n-bit number
Xn[1] = an //nth input of an
Xn[2] = bn //nth input of bn
Xn[3] = 0
Xn[4] = 1
If Xn[1] Xn[2] then
Yn[2] = Ryn=1
Else if Xn[1] Xn[2] then
Yn[4] = Qyn=1
to be Yn and Yn-1 respectively
Loop
For j = n - 1 to 1
Pick up TR_BME_FG Comparator cell WJ
If j = n-1 then
WJ[1] = Xn[4] = QYn
WJ[2] = Xn[1] = PYn
WJ[3] = bn-1
WJ[4] = an-1
Else
WJ[1] = WJ-1[2] = QYn-1
WJ[2] = WJ-1[1] = PYn-1
WJ[3] = aj //(n-1)th input of an
WJ[4] = bj //(n-1)th input of bn
End if
End loop
Step 3. Pick up F_F Comparator cell and pick input V and output Z
V[1]= W[1]
V[2] = W[2]
V[3] = 0
Z[1] = W[1]
Z[2] = [W[1]⊗ W[2]]⊗ 1
Z[3] = W[2]
End
7. MOS TRANSISTOR IMPLEMENTATION OF DIFFERENT
COMPARATOR CELL
In this section implement different comparator cell in MOS transistor with minimum MOS
transistor count. MOS transistor implementations of 2-bit comparator uses 14 MOS transistors,

TR_BME_FG Comparator cell required 18 MOS transistor and for F_F comparator cell require 4
MOS transistor. These cells are connected for required 2-bit, 8-bit and 64-bit reversible
comparator operation and analyzed in terms of power consumption, delay and power delay
product (PDP).
24
Figure 10. MOS transistor implementation of Figure 11. MOS transistor implementation of
1- bit Comparator Cell F_F Comparator Cell
Figure 12. MOS transistor implementation of TR_BME_FG Comparator Cell

25
8. SIMULATION RESULT AND DISCUSSION
Novel design of 2-bit, 8-bit, 64-bit and n-bit group-based reversible comparator is implemented
in T-Spice and optimized the speed, power for appropriate W/L ratio using 90nm technology
node. Individual cell performance parameters analyse for reducing input voltage and finding
power consumption, delay etc.
Figure 13. Simulation output of 1-bit comparator
0.8 1 1.2 1.4
5
4
3
2
1
0
Power (xE-06)
0.6 0.6
Input Voltage (V)
0.8 1 1.2 1.4
2.5
2
Delay (xE-08)
1.5
1
0.5
0
Input Voltage (V)
Figure 14. Power and delay Comparison at different input voltage of 1-bit comparator.

26
4
3.5
3
2.5
2
1.5
1
0.5
0
Input Voltage versus Power delay product
Power delay Product
0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5
Input Voltage (V)
Figure 15. Input voltage versus Power delay product (PDP) of 1-bit Comparator.
Figure 16. Simulation output of 2-bit comparator
PDP (xE-14ws)
0.8 1 1.2 1.4 1.6
9
8
7
6
5
4
3
2
1
0
x 10
-5
Input Voltage (V)
Power (xE-05)
0.8 1 1.2 1.4 1.6
7
6
5
4
3
2
1
0
x 10
-8
Input Voltage (V)
Delay (xE-08)
Figure 17. Power and delay Comparison at different Input voltage of 2-bit comparator.

10
8
6
4
2
Maximum Power and Delay Variation(s) versus Channel Length Variation(u)
Maximum Power variation (xE-05)
Maximum Delay variation (xE-08)
1 2 4 6 8
27
1
0.8
0.6
0.4
0.2
0
x 10
-12
0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5
Input Voltage (V)
PDP (xE-13)
Figure 18. Input voltage versus Power delay product (PDP) of 2-bit Comparator.
Channel Length Variation (nm)
Figure 19. Channel Length Variation versus power and delay of 2-bit Comparator
Table 2. Comparison between anticipated and existing in terms of expertise of reversible gate
RGate Gate can be used as n-bit
comparator
Single Gate can be
used as Full
subtractor
Gate can be
used as n-to-2n
decoder
Anticipated Inventive
Gate
Y Y Y
Available Circuit [4] Y N N
Available Circuit [3] N N Y
Available Circuit [12] N N N
Available Circuit [6] Y N N
Available Circuit [5] Y Y N

Table 3. Comparison between anticipated and existing style comparator in terms of NOG, GO, CI, power
28
and delay
Methods NOG GO CI Power (μW) Delay (ns)
Anticipated work 6+4(n-1) 1+4(n-1) 1+2n
NOG-number of gate, GO-Garbage output, CI-Constant input
Table 4 Comparison between anticipated and existing style Comparator in terms of garbage output and
constant input
(85.81n – 78.98)
(115.010n – 100.854)
Thaplial et al.
[17]
9n (6n −6) -- (268.23n −239.2) {0.23 x log2(n) + 0.1}
Vudadha et al.
[18]
(4n −2) (5n −4) -- (122.36n −60.36) {0.09*log2(n) + 0.2}
Rangaraju et al.
[7 ]
(7n −4) (5n −4) -- (182.53n +76.55) (0.2n − 0.16)
Hafiz Md. Hasan
Babu [ 4]
3n (4n-3) 3 (117.76n −32.94) (0.15n − 0.03)

29
9. CONCLUSION AND FUTURE WORK
This paper is mainly focused on novel design of the reversible 4x4 inventive Gate. It utilized as
1-bit, 2-bit, 8-bit, 32-bit and n-bit group-based binary comparator and n-to-2n decoder. Moreover,
the low value styles of reversible parameter have been established for the proposed circuits. For
example, and n-to-2n decoder uses at least 2n + 1 reversible gates and its n garbage output: an n-bit
comparator utilize 6+4 (n - 1) number of reversible gate, 1+4 (n-1) garbage output. The
proposed group- based comparator achieves the improvement of 19.87% in terms of garbage
output and 31.57% in terms of constant input over the existing one [7]. Simulation of the novel
comparator circuits have shown that it works correctly and finding parameter power and delay.
The proposed circuits will be useful for implementing the ALU and control unit of processor.
ACKNOWLEDGMENT
Authors would like to acknowledge Research Cum Teaching Fellowship through TEQIP-II
provide by World Bank for the financial support for this work.
REFERENCES
[1] J R.Landauer, “Irreversibility and Heat Generation in the Computational Process”, IBM Journal of
Research and Development, pp: 183-191, 1961.
[2] C H Bennett, “Logical Reversibility of Computation,” IBM Journal of Research and Development,
vol. 17, no. 6, pp. 525-532,November 1973.
[3] Lafifa Jamal, Md. Masbaul Alam, Hafiz Md. Hasan Babu “An efficient approach to design a
reversible control unit of a processor” Elsevier Sustainable Computing: Informatics and Systems pp:
286-294, 2013
[4] Hafiz Md. Hasan Babu, Nazir Saleheen, Lafifa Jamal, Sheikh Muhammad Sarwar,Tsutomu Sasao
Approach to design a compact reversible low power binary comparator IET Computers Digital
Techniques Vol. 8, Iss. 3, pp. 129–139 doi: 10.1049/iet-cdt.2013.0066, 2014
[5] Ri-gui Zhou, Man-qun Zhang, QianWu •Yan-cheng Li Optimization Approaches for Designing a
Novel 4-Bit Reversible Comparator Springer International jounal of theoretical physics DOI
10.1007/s10773-012-1360-y pp:559-575, 2013
[6] Farah Sharmin, Rajib Kumar Mitra, Rashida Hasan, Anisur Rahman Low cost reversible signed
comparator International Journal of VLSI design Communication Systems” Vol.4, No.5,pp:19-
33,2013
[7] Rangaraju H G, Vinayak Hegdeb, Raja K B, Muralidhara K N Design of Efficient Reversible Binary
Comparator Elsevier International Conference on Communication Technology and System Design
Procedia Engineering pp:897-904, 2012
[8] Rangaraju, H.G., Hegde, V., Raja, K.B., Muralidhara, K.N. “Design of low power reversible binary
comparator”. Proc. Engineering (ScienceDirect), 2011
[9] Bahram Dehghan, Abdolreza Roozbeh, Jafar Zare Design of Low Power Comparator Using DG
Gate Scientific research ciruits and systems doi.org/10.4236/cs.2013.51002pp: 7-12, 2014
[10] Pallavi Mall , A.G.Rao, H.P.Shukla Novel Design of Four-Bit Reversible Numerical Comparator
International Journal of Advanced Research in Computer and Communication Engineering Vol. 2,
Issue 4 pp:1808-1807, 2013
[11] Neeta Pandey, Nalin Dadhich, Mohd. Zubair Talha Realization of 2-to-4 reversible decoder and its
applications International Conference on Signal Processing and Integrated Networks (SPIN) pp:349-
353,2014
[12] Md. M. H Azad Khan, “Design of Full-adder With Reversible Gates”,International Conference on
Computer and Information Technology,Dhaka, Bangladesh, 2002, pp. 515-519

[13] Hafiz Md. Hasan Babu, Md. Rafiqul Islam, Syed Mostahed Ali Chowdhury and Ahsan Raja
Chowdhury ,“Reversible Logic Synthesis for Minimization of Full Adder Circuit”, Proceedings of the
EuroMicro Symposium on Digital System Design(DSD’03), 3-5 September 2003,
30
[14] Neeraj Kumar Misra, Subodh Wairya, Vinod Kumar Singh “Preternatural Low-Power Reversible
Decoder Design in 90 nm Technology Node” International Journal of Scientific Engineering
Research, Volume 5, Issue 6, pp: 969-978, June 2014
[15] J.W. Bruce, M.A. Thornton,L. Shivakumariah, P.S. Kokate and X.Li, Efficient Adder Circuits Based
on a Conservative Logic Gate, Proceedings of the IEEE Computer Society Annual Symposium on
VLSI(ISVLSI'02),April 2002, Pittsburgh, PA, USA, pp 83-88.
[16] Lafifa Jamal, Md. Masbaul Alam Polash On the Compact Designs of Low Power Reversible
Decoders and Sequential Circuits Springer LNCS7373, pp. 281–288, 2012.
[17] Himanshu Thapliyal, Nagarajan Ranganathan and Ryan Ferreira Design of a Comparator Tree Based
on Reversible Logic 10th IEEE International Conference on Nanotechnology Joint Symposium with
Nano Korea pp:1113-1116, 2010
[18] Vudadha, C.Phaneendra, P.S.,Sreehari,V.Ahmed,S.E.Muthukrishnan, N.M.Srinivas “Design of
prefix-based Optimal reversible comparator” IEEE Computer Society Annual Symp. On VLSI pp.
201–206
[19] Nagamani, A.N., Jayashree, H.V., Bhagyalakshmi, H.R.: ‘Novel low power comparator design using
reversible logic gates’, Indian J. Comput. Sci. Eng.vol 2, (4), pp. 566–574, 2011
[20] Morrison, M., Lewandowski, M., Ranganathan “Design of a tree-based comparator and memory unit
based on a novel reversible logic structure” IEEE Computer Society Annual Symp. on VLSI, pp.
331–336, 2012
[21] Neeraj Kumar Misra, Subodh Wairya, Vinod Kumar Singh “An Inventive Design of 4*4 Bit
Reversible NS Gate” IEEE International Conference on Recent Advances and Innovation in
Engineering (ICRAIE-2014), pp: 1-6, 2014 doi no. 10.1109/ICRAIE.2014.6909323

Evolution of Structure of Some Binary Group-Based N-Bit Compartor, N-To-2N Decoder by Reversible Technique

Recommended

More Related Content

What's hot (16)

Viewers also liked (19)

Similar to Evolution of Structure of Some Binary Group-Based N-Bit Compartor, N-To-2N Decoder by Reversible Technique (20)

Recently uploaded (20)

Evolution of Structure of Some Binary Group-Based N-Bit Compartor, N-To-2N Decoder by Reversible Technique