Automation Networking By Shivam Singh
Download as pptx, pdf3 likes1,444 views
The document discusses several topics related to computer network architecture and protocols. It begins by defining network architecture as a framework for designing, building, and managing communication networks. It describes the OSI 7-layer model and each of its layers. It also discusses the TCP/IP network architecture, IP addressing formats and classes, TCP and UDP protocols, and serial communication modes like simplex, half-duplex and full-duplex.
More Related Content
What's hot (20)
Viewers also liked (16)
Similar to Automation Networking By Shivam Singh (20)
More from Shivam Singh (6)
Recently uploaded (20)
Automation Networking By Shivam Singh
- 2. Network Architecture Network architecture is a blueprint of the complete computer communication network, which provides a framework and technology foundation for designing, building and managing a communication network. Anyone is free to design hardware and software based on the network architecture. The TCP/IP network architecture, which the Internet is based on, is such as open network architecture and it is adopted as a worldwide network standard and widely deployed in local area network (LAN), wide area network (WAN), small and large enterprises, and last but not the least, the Internet. Open Systems Interconnection (OSI) network architecture, developed by International Organization for Standardization, is an open standard for communication in the network across different equipment and applications by different vendors. Network architecture provides only a conceptual framework for communications between computers. Actual communication is defined by various communications protocols.
- 3. OSI 7 Layers Model Open Systems Interconnection (OSI) model is a reference model developed by ISO (International Organization for Standardization) in 1984, as a conceptual framework of standards for communication in the network across different equipment and applications by different vendors.
- 4. OSI 7 Layers Model…… The OSI model defines the communications process into 7 layers, dividing the tasks involved with moving information between networked computers into seven smaller, more manageable task groups. Basically, layers 7 through 4 deals with end to end communications between data source and destinations, while layers 3 to 1 deal with communications between network devices. On the other hand, the seven layers of the OSI model can be divided into two groups: Upper layers (layers 7, 6 & 5) and Lower layers (layers 4, 3, 2, 1). The upper layers of the OSI model deal with application issues and generally are implemented only in software. The highest layer, the application layer, is closest to the end user. The lower layers of the OSI model handle data transport issues. The physical layer and the data link layer are implemented in hardware and software. The lowest layer, the physical layer, is closest to the physical network medium (the wires, for example) and is responsible for placing data on the medium.
- 5. OSI 7 Layers Model…… Layer 7: Application Layer • Defines interface to user processes for communication and data transfer in network. • Provides standardized services such as virtual terminal, file and job transfer and operations. Layer 6: Presentation Layer • Masks the differences of data formats between dissimilar systems. • Specifies architecture-independent data transfer format. • Encodes and decodes data; encrypts and decrypts data; compresses and decompresses data. Layer 5: Session Layer • Manages user sessions and dialogues. • Controls establishment and termination of logic links between users. • Reports upper layer errors. Layer 4: Transport Layer • Provides reliable and sequential packet delivery through error recovery and flow control mechanisms. • Provides connectionless oriented packet delivery and Manages end-to-end message delivery in network.
- 6. OSI 7 Layers Model…… Layer 3: Network Layer • Determines how data are transferred between network devices • Routes packets according to unique network device addresses • Provides flow and congestion control to prevent network resource depletion Layer 2: Data Link Layer • Defines procedures for operating the communication links • Frames packets • Detects and corrects packets transmit errors Layer 1: Physical Layer • Defines physical means of sending data over network devices • Interfaces between network medium and devices • Defines optical, electrical and mechanical characteristics
- 7. Internet Protocol (IP) The Internet protocols are the world’s most popular opensystem (nonproprietary) protocol suite because they can be used to communicate across any set of interconnected networks and are equally well suited for LAN and WAN communications. The Internet protocols consist of a suite of communication protocols, of which the two best known are the Transmission Control Protocol (TCP) and the Internet Protocol (IP). The Internet protocol suite not only includes lower-layer protocols (such as TCP and IP), but it also specifies common applications such as electronic mail, terminal emulation, and file transfer.
- 9. IP Addressing As with any other network-layer protocol, the IP addressing scheme is integral to the process of routing IP datagrams through an internetwork. Each IP address has specific components and follows a basic format. Each host on a TCP/IP network is assigned a unique 32-bit logical address that is divided into two main parts: the network number and the host number. The network number identifies a network and must be assigned by the Internet Network Information Center (InterNIC) if the network is to be part of the Internet. An Internet Service Provider (ISP) can obtain blocks of network addresses from the InterNIC and can itself assign address space as necessary. The host number identifies a host on a network and is assigned by the local network administrator.
- 10. IP Address Format The 32-bit IP address is grouped eight bits at a time, separated by dots, and represented in decimal format (known as dotted decimal notation). Each bit in the octet has a binary weight (128, 64, 32, 16, 8, 4, 2, and 1). The minimum value for an octet is 0, and the maximum value for an octet is 255.
- 11. IP Address ClassesIP addressing supports five different address classes: A, B, C, D, and E. Only classes A, B, and C are available for commercial use. The left-most (high-order) bits indicate the network class.
- 13. IP Subnet Addressing IP networks can be divided into smaller networks called sub-networks (or subnets). Sub-netting provides the network administrator with several benefits, including extra flexibility, more efficient use of network addresses, and the capability to contain broadcast traffic (a broadcast will not cross a router). Subnets are under local administration. As such, the outside world sees an organization as a single network and has no detailed knowledge of the organization’s internal structure. A given network address can be broken up into many subnetworks. For example, 172.16.1.0, 172.16.2.0, 172.16.3.0, and 172.16.4.0 are all subnets within network 171.16.0.0. (All 0s in the host portion of an address specifies the entire network.)
- 14. Transmission Control Protocol (TCP) The TCP provides reliable transmission of data in an IP environment. TCP corresponds to the transport layer (Layer 4) of the OSI reference model. Among the services TCP provides are stream data transfer, reliability, efficient flow control, full-duplex operation, and multiplexing. TCP offers reliability by providing connection-oriented, end-to-end reliable packet delivery through an internetwork. It does this by sequencing bytes with a forwarding acknowledgment number that indicates to the destination the next byte the source expects to receive. TCP offers efficient flow control, which means that, when sending acknowledgments back to the source, the receiving TCP process indicates the highest sequence number it can receive without overflowing its internal buffers. Full-duplex operation means that TCP processes can both send and receive at the same time. Finally, TCP’s multiplexing means that numerous simultaneous upper-layer conversations can be multiplexed over a single connection.
- 15. User Datagram Protocol (UDP) The User Datagram Protocol (UDP) is a connectionless transport-layer protocol (Layer 4) that belongs to the Internet protocol family. UDP is basically an interface between IP and upper-layer processes. UDP protocol ports distinguish multiple applications running on a single device from one another. Unlike the TCP, UDP adds no reliability, flow-control, or error-recovery functions to IP. Because of UDP’s simplicity, UDP headers contain fewer bytes and consume less network overhead than TCP. UDP is useful in situations where the reliability mechanisms of TCP are not necessary, such as in cases where a higher-layer protocol might provide error and flow control. UDP is the transport protocol for several well-known application-layer protocols, including Network File System (NFS), Simple Network Management Protocol (SNMP), Domain Name System (DNS), and Trivial File Transfer Protocol (TFTP).
- 17. Serial Communication The RS stands for Recommended Standard. Nothing was really agreed upon or official. At least not in the sense of the "made-by-committee" standards like IEEE1284 and IEEE-1394. Simplex can be viewed as a communications "one-way street". Data only flows in one direction. That is to say, a device can be a receiver or a transmitter exclusively. A simplex device is not a transceiver. A good example of simplex communications is an FM radio station and your car radio Duplex communications overcome the limits of Simplex communications by allowing the devices to act as transceivers. Duplex communication data flows in both directions thereby allowing verification and control of data reception/transmission. Full Duplex devices can transmit and receive data at the same time. RS232 is a fine example of Full Duplex communications. There are separate transmit and receive signal lines that allow data to flow in both directions simultaneously. RS422 devices also operate Full Duplex. Half Duplex devices have the dubious honor of allowing both transmission and receiving, but not at the same time. Essentially only one device can transmit at a time while all other half duplex devices receive. Devices operate as transceivers, but not simultaneous transmit and receive
- 18. DCE and DTE Devices DTE stands for Data Terminal Equipment, and DCE stands for Data Communications Equipment. These terms are used to indicate the pin-out for the connectors on a device and the direction of the signals on the pins. Your computer is a DTE device, while most other devices such as modem and other serial devices are usually DCE devices. DTE DCE 25 pin male pin-out 25 pin female pin-out Pin 1 - Shield Ground Pin 1 - Shield Ground Pin 2 - Transmitted Data (TD) output Pin 2 - Transmitted Data (TD) input Pin 3 - Receive Data (RD) input Pin 3 - Receive Data (RD) output Pin 4 - Request To Send (RTS) output Pin 4 - Request To Send (RTS) input Pin 5 - Clear To Send (CTS) input Pin 5 - Clear To Send (CTS) output Pin 6 - Data Set Ready (DSR) input Pin 6 - Data Set Ready (DSR) output Pin 7 - Signal Ground Pin 7 - Signal Ground Pin 8 - Carrier Detect (CD) input Pin 8 - Carrier Detect (CD) output Pin 20 (DTR) output Data Terminal Pin 22 - Ring Indicator (RI) input Ready Pin 20 (DTR) input Data Terminal Pin 22 - Ring Indicator (RI) output Ready
- 19. Synchronous Data Transfer- In program-to-program communication, synchronous communication requires that each end of an exchange of communication respond in turn without initiating a new communication. A typical activity that might use a synchronous protocol would be a transmission of files from one point to another. As each transmission is received, a response is returned indicating success or the need to resend.
- 20. Asynchronous Data Transfer The term asynchronous is usually used to describe communications in which data can be transmitted intermittently rather than in a steady stream. For example, a telephone conversation is asynchronous because both parties can talk whenever they like. If the communication were synchronous, each party would be required to wait a specified interval before speaking. The difficulty with asynchronous communications is that the receiver must have a way to distinguish between valid data and noise. In computer communications, this is usually accomplished through a special start bit and stop bit at the beginning and end of each piece of data. For this reason, asynchronous communication is sometimes called Start-Stop Transmission.
- 21. Handshaking Handshaking is a procedure used to check the link between DTE & DCE before transmitting of data. Data is transmitted and received on pins 2 and 3 respectively (for both types 25 & 9 pin). 1. DTE would request to send data to DCE (RTS). 2. The DCE will indicate to DTE that it is ready and clear to send data (CTS). Both RTS and CTS therefore used to control data flow between DTE & DCE. Data Set Ready (DSR) is an indication from the DCE (i.e., the modem) that it is ON. Similarly, DTR (i.e., the PC) indicates to the Data Set that the DTE is on. Data Carrier Detect (CD) indicates that a good carrier is being received from the remote modem.
- 22. RS-232 RS-232 (Recommended standard-232) is a standard interface approved by the Electronic Industries Association (EIA) for connecting serial devices. In other words, RS-232 is a long established standard that describes the physical interface and protocol for relatively lowspeed serial data communication between computers and related devices. An industry trade group, the EIA, defined it originally for teletypewriter devices. In 1987, the EIA released a new version of the standard and changed the name to EIA-232-D. Many people, however, still refer to the standard as RS-232C, or just RS- 232. RS-232 is the interface that your computer uses to talk to and exchange data with your modem and other serial devices. The serial ports on most computers use a subset of the RS- 232C standard.
- 23. RS-232……. 9-pin D-type connector Pin assignment
- 24. RS-232……. 25-pin D-type connector Pin assignment
- 25. RS-232……. Type of Cables- (A) Modem Cable: A normal modem cable runs straight through with pin 1 to pin 1, pin 2 to pin 2 etc. The end that will be connected to the terminal or PC is a female connector, and the end that will be connected to the modem is male connector.
- 26. RS-232……. (B) Null Modem Cables: When you need to connect two equipment with both (DTE) or both (DCE), for example connecting two PC's, then in this case you have to use the cable with below pin connection (25 to 25). And this is called Null modem cable. “Connecting 25 pin to 25 pin for Null modem”
- 27. RS-232……. “Connecting 9 pin to 9 pin for Null Modem”
- 28. RS-232……. “Connecting 9 pin to 25 pin for Null Modem”
- 29. RS-485 RS-485 allows multiple devices (up to 32) to communicate at half-duplex on a single pair of wires, plus a ground wire (more on that later), at distances up to 1200 meters (4000 feet). Both the length of the network and the number of nodes can easily be extended using a variety of repeater products on the market. Data is transmitted differentially on two wires twisted together, referred to as a “twisted pair.” The properties of differential signals provide high noise immunity and long distance capabilities. A 485 network can be configured two ways, “twowire” or “four-wire.” In a “two-wire” network the transmitter and receiver of each device are connected to a twisted pair. “Four-wire” networks have one master port with the transmitter connected to each of the “slave” receivers on one twisted pair. The “slave” transmitters are all connected to the “master” receiver on a second twisted pair.
- 30. RS-485…… The EIA RS- 485 Specification labels the data wires “A” and “B”, but many manufacturers label their wires “+” and “-”. In our experience, the “-” wire should be connected to the “A” line, and the “+” wire to the “B” line. Reversing the polarity will not damage a 485 device, but it will not communicate. This said, the rest is easy: always connect A to A and B to B.
- 31. RS-422 The TIA/EIA-422 standard, known as RS422, describes a communication interface that uses balanced data transmission over multiple pairs of wires to establish communication from one transmitter to up to 10 receivers. At least two twisted pairs of wires are used, one for communication from the transmitter (usually the master) to the receivers (usually the slaves), and the other for transmission from the slaves back to the master. RS-422 is similar to RS-232, and can be programmed in the same way, however, offers a few advantages and disadvantages. One problem is that you need to purchase an RS-422 port or at least an RS-422 to RS-232 converter, since PC's don't come standard with this interface. Also, you may find that there are fewer devices supporting RS-422.
- 32. RS-422……. Some advantages are: 1. Long Distance Runs - Up to 500 feet is generally supported, and with repeaters, even further distances can be achieved. 2. Multi-Drop - Usually, up to 32 devices can be connected per port, and even more using repeaters. Devices are distinguished by unique addresses that are assigned to each device. 3. Noise Resistant - Since it uses a separate FLOATING transmit and receive pair (four wires), it offers better noise immunity than RS-232.
- 33. Comparison-