1 . introduction to communication system

21/06/15 1
Chapter 1:
Communication System
An Introduction

21/06/15 2
Communications
 Communications
Transfer of information from one place to another.
Should be efficient, reliable and secured.
“A communication system is a process of conveying
information from a source to a destination”
 Communication system
Components/subsystems act together to
accomplish information transfer/exchange
“An electronic communication system is transferring
information using an electrical field as a mean of signal”

21/06/15 3
Requirements
 Rate of information transfer
 The rate of information transfer is defined as the amount of
information that must be communicated from source to
destination.
 It will determined the physical form and technique used to
transmit and receive information and therefore determines
the way system is designed and constructed
 Purity of signal received
 The received signal must be the same as the transmitted
signal

21/06/15 4
 Simplicity of the system
 Any communication system must be convenient in order to be
effective and efficient and easy to use
 Reliability
 Users must be able to depend on a communication system. It
must work when needed and transmit and receive information
without errors or with an acceptable error.
Requirements

21/06/15 5
Elements of Communication system
Input
Transducer
Transmitter
Channel
Receiver
Output
Transducer
Input
Message
Output
Message
Transmission
medium
noise

21/06/15 6
 Input Transducer
To convert the message to a form suitable for the
particular type of communication system.
Eg: Speech waves are converted to voltage
variation by a microphone.
 Transmitter
Processes the input signal  to produce a transmitted signal that
suited the characteristic of transmission channel.
eg: modulation, coding
Other functions performed:
Amplification, filtering

21/06/15 7
 Channel (Transmission medium)
A medium that bridges the distance from source to destination.
eg: Atmosphere (free space), coaxial cable, fiber optic,
waveguide
Signal undergoes degradation from noise, interference and distortion.
 Transmission systems can be evaluated according to five (5) main
criteria:
 Capacity  Performance
 Distance  Security
 Cost which include installation, operation and maintenance

21/06/15 8
The two main categories of channel commonly used are:
 Line (conducted media)
 The channel is made up metallic cable (such as coaxial
cable, twisted pair, parallel wires, and others) or fibre optic
cable.
 Free space or radiated media
 This is the medium where the transmission of signal is
carried out by the propagation of electromagnet wave.
 The main applications are in radio broadcasting,
microwaves and satellites transmission systems.

21/06/15 9
• Loses in medium of transmission
• However, each medium introduces losses termed as
attenuation, distortion and adds noise to some degree to the
transmitted signal. The amount of attenuation, distortion and
noise depends on the type of transmission medium used.
• There is normally no signal processing in the transmission
medium, it is just the medium where the transmitter is
connected to the receiver.

21/06/15 10
 Receiver
To extract the desired signal from the output channel and to
convert it to a form suitable for the output transducer.
eg: Demodulation, decoding
Other functions performed:
Amplification, filtering.
 Output Transducer
Converts the electrical signal at its input into a form desired by
the system used.
Eg: Loudspeaker, PC and tape-recorders.

21/06/15 11
Various unwanted undesirable effect crop up in transmissions
 Attenuation
 Reduces signal strength at the receiver
 Distortion
 Waveform perturbation caused by imperfect response of the
system to the desired signal itself
 Equalizer can be used to reduced the effect
 Interference
 Contamination by extraneous signals from human sources
Losses in Communication System

21/06/15 12
 Noise
 Random and unpredictable electrical signals from internal or
external to the system
 The term SNR (signal to noise ratio) is used to measure
performance (noise) relative to an information analog signal
 The term BER (Bit Error Rate) is used in digital system to
measure the deterioration of the signal
Losses in Communication System

21/06/15 13
Analog vs. Digital
The signal can be analog or digital message:
 Analog
 Continuous Variation
- Assumes the total range of frequencies/time
 All information is transmitted.
 Digital
 Takes samples
- non-continuous stream of on/off pulses
 Translates to 1s and 0s

21/06/15 14
Analog Vs Digital
(Advantages and Disadvantages)
Digital CS Analog CS
Advantages:
 Inexpensive
 Privacy preserved (Data
encrypt.)
 Can merge different data
 Error correction
Disadvantages:
 Expensive
 No privacy preserved
 Cannot merge different data
 No error correction capability
Disadvantages:
 Larger bandwidth
 Synchronization problem is
relatively difficult.
Advantages:
 Smaller bandwidth
 Synchronization problem is
relatively easier.

21/06/15 15
Baseband vrs Modulated Signal
 Baseband Signal
 Base band signal is the modulating signal/original information
signal either in a digital or analog form (intelligent/message) in
communication system
Example: voice signal (300Hz – 3400Hz)
 Transmission of original information whether analog or digital,
directly into transmission medium is called baseband
transmission.
 Modulated Signal
 Modulated signal is baseband signal which its original frequency
is shifted to higher frequency to facilitate transmission
purposes

21/06/15 16
Block Diagram of Modulation Process
MODULATION
PROCESS
Baseband
signal
Modulated
signal
Carrier

21/06/15 17
Baseband Transmission
 The need of baseband transmission:
 The concepts and parameter of baseband transmission are
used in modulated transmission
 Performance of baseband transmission is used as the standard
for comparing modulation techniques
 Baseband signal is not suitable for long distance communication
because:
 Hardware limitation (eg: requires very long antenna)
 Interference with other waves

21/06/15 18
Modulation
 Modulation –
Process of changing baseband signals to facilitate
the transmission medium
 Process of modulation
 Frequency translation such as AM, FM, PM etc
 Sampling and coding such as PAM, PCM etc
 Keying such as ASK, FSK etc

21/06/15 19
 Types of modulation :
 Analogue modulations are frequency translation method
caused by changing the appropriate quantity in a carrier
signal
 Digital modulation is the result of changing analogue signal
into binary ones by sampling and coding
 Keying modulations are digital signals subsequently
modulated by the frequency modulation by using one or other
analogue method
Modulation

21/06/15 20
Why Modulate?
 Reduce noise and interference
 By using proper frequency where noise and interference are
at minimum
 Increasing power is costly and may damage equipment
 Frequency Assignment
 For TV and radio broadcasting, each station has a different
assigned carrier
 Multiplexing
 Combining several signals for simultaneous transmission on
one channel by placing each signal on different carrier
frequency

21/06/15 21
Electromagnetic Frequency Spectrum
 The electromagnetic frequency spectrum is divided into
 subsections, or bands, with each band having a different
name and boundary
 The International Telecommunications Union (ITU) is an
international agency in control of allocating frequencies and
services within the overall frequency spectrum

21/06/15 22
# Speed of electromagnetic wave = speed of light, c = 3.0x108
ms-1
c λf=
f = freq
λ = wavelength
 In the United State, the Federal Communications Commission
(FCC) assigns frequencies and communications services for free
space radio propagation
Electromagnetic Frequency Spectrum

21/06/15
Communication System: Introduction
Prof. Hendre V.S., TCOER, Pune 23

21/06/15 24
Frequency allocation
 If the transmission channel is the atmosphere,
interference and propagation are strongly dependent on the
transmission frequency
 On international basis, frequency assignment and technical
standards are set by the ITU
 There are three main sector that provides frequency assignment
and is concerned with the efficient use of radio frequency
spectrum
 ITU(R)
 ITU(T)
 ITU(D)

21/06/15 25
Frequency Bands
3 – 30 kHz VLF (very low freq) Ground wave
30 – 300 kHz LF (low freq) Ground wave
300 – 3000 kHz MF (medium freq) Ground wave/sky wave
3 – 30 MHz HF (high
freq) Sky wave (Ionospheric)
30 – 300 MHz VHF (very high freq) Space wave (LOS)
300 – 3000 MHz UHF (ultrahigh freq) Space wave (LOS)
3 – 30 GHz SHF (superhigh freq) LOS/Satellite
30 – 300 GHz EHF (Extremely high freq) LOS/Satellite
International Telecommunications Union (ITU) Band Designation

21/06/15 26
Frequency Bands Letter Designation
1.0 – 2.0 GHz L
2.0 – 4.0 GHz S
4.0 – 8.0 GHz C
8.0 – 12.0 GHz X
12.0 – 18.0 GHz Ku
18.0 – 27.0 GHz K
27.0 – 40.0 GHz Ka
26.5 – 40.0 GHz R
Frequency Bands
Federal Communications Commission (FCC) Emission Classifications

21/06/15 27
Frequency Bands Letter Designation Uses
33.0 – 50 GHz Q Radar/satellite comm
40.0 – 75.0 GHz V Radar/satellite comm
75.0 – 110 GHz W Radar/satellite comm
103
– 107
GHz Infrared, visible Optical communication
light and ultra violet
Frequency Bands
Federal Communications Commission (FCC) Emission Classifications

21/06/15 28
Radio Communication System
 It is wireless communication system
 The information is being carried by the electromagnetic waves,
which is propagated in free space
 Electromagnetic waves are waves that travel at the speed of light
and made up of an electrical field and magnetic field at right
angles to one another and to the direction of propagation

21/06/15 29
Transmitter Receiver
Transmitting
antenna
Receiving
antenna
Block diagram of a radio communication system
Radio Communication System

21/06/15 30
Propagation Waves
There are three main type of propagations:
 Ground wave propagation
 Dominants mode for frequencies below 2 MHz
 The movement tend to follow the contour of the earth with
large antenna size
 Sky-wave propagation
 Dominants mode for frequencies between 2 – 30 MHz range
 Coverage is obtained by reflection the wave at ionosphere
and at the earth boundaries
 This is because the index refractions of the ionosphere
varies with the altitude as the ionization density changes

21/06/15 31
Propagation Waves
 There are areas of no coverage along the earth surface
between transmitting and receiving antenna
 The angle of reflection and the loss of signal depend on the
frequency, time, season, activities of the sun etc
 Space wave propagation (LOS)
 Dominants mode for frequencies above 30 MHz where in
propagates in straight line
 No refraction and can almost propagates through ionosphere

21/06/15 32
Propagation Waves
 But the signal path has to be above horizon to avoid blocking
leading antenna to be placed on tall towers
 The distance to radio horizon is
d = √2h miles
Sky-wave propagation
Space-wave propagation
Ground-wave propagation

21/06/15 33
Propagation Waves
 The three waves propagation methods:
 Ground wave propagation
 Sky wave propagation
 Space wave propagation
Earth
Ionospheric layer
Sky wave
propagation
Space wave propagation
Transmitter
Receiver
Fig: Radio wave propagation methods

21/06/15 34
Propagation Waves
 Ground (surface) wave
 Wave that progress along the surface the earth
 It follows the curvature of the earth
 Sky wave propagation
 Sky waves are those waves that radiated towards
ionosphere. By a process of refraction and reflection, the
receiver on the earth will receive the signal. The various
layers of the ionosphere have specific effects on the
propagation of radio waves

21/06/15 35
Propagation Waves
 Space wave
 The wave is propagated in a straight line
 space wave is limited in their propagation by the
curvature of the earth
 sometimes it is called direct wave or line-of-sight (LOS)
 The radio horizon of the antenna is the distance
between the transmitter and receiver and is denoted by
d,
where
in km
and and

21/06/15 36
Propagation Waves
 dt = radio horizon of the transmitting antenna, in km
 ht = height of transmitting antenna, in m
 dr = radio horizon of the receiving antenna, in km
 hr = height of receiver antenna, in m
Transmitter
Receiver
Fig: Line of sight propagation
dt
dr
LOS propagation
d

21/06/15 37
Satellite Communication
 Satellite employs LOS radio transmission over very long distance
 It offers brad coverage even across the ocean and can handle
bulk of very long distance telecommunication
Satellite
uplink
down-link

21/06/15 38
Historical Development
Year Events
1844
1876
1904
1923
1936
1962
1966
1972
Telegraph
Telephone
AM Radio
Television
FM Radio
Satellite
Optical links using laser and fiber optics
Cellular Telephone

21/06/15 39
Historical Development
Year Events
1975
1975
1980
1981
1982
1985
1989
1990
1990-2000
First digital telephone switch
Wideband communication system (cable TV etc)
Compact disc is developed by Philip & Sony
FCC adopts rules for commercial cellular telephone
Internet is used to replace ARPANET
Fax machines widely available in offices
First SONET standard optical fiber products released
WWW becomes part of the internet
Digital communication system (ISDN, BISDN, HDTV,
handheld computers, digital cellular etc Global
telecom system

21/06/15 40
Power Measurement (dB, dBm)
 The decibel (dB) is a transmission-measuring unit used to
express gain and losses an electronic devices and circuits
 for describing relationship between signal and noise
 dB  1W
 dBm  1mW
 example: 100W = 10 log10 100 = 2dB
= 10 log10 100 = 50 dBm
1mW

21/06/15 41
 If two powers are expressed in the same unit (eg: watts or
microwatts), their ratio is a dimensionless quantity that can
be expressed in decibel form as follows:
)(log10dB
2
1
10
P
P
=
Where P1 = power level 1 (watts)
P2 = power level 2 (watts)
The dB value is the difference in dB between P1 and P2

21/06/15 42
 When used in electronic circuits to measure a power gain or loss,
that equation can rewritten as
)(log01Gain 10(dB)
in
out
P
P
=
Where Gain (dB) = power gain (dB)
Pout = output power level (watts)
Pin = input power level (watts)
=
in
out
P
P
absolute power
• (+) dB - power gain
•output power is greater than input power
• (-) dB power loss
•output power is less than input power

21/06/15 43
Examples
1. Convert the absolute power ratio of 200 to a power gain in dB
Solution:
Power gain, Ap (dB) = 10 log10 [200]
= 10(2.3)
= 23 dB
2. Convert the power gain Ap = 23 dB to an absolute power ratio
Solution
Power gain, Ap (dB) = 10 log10 [Pout/Pin]
2.3 = log10 [Pout/Pin]
[Pout/Pin] = antilog 2.3
= 200

21/06/15 44
Examples
3. Convert a power level of 200mW to dBm
Solutuion:
dBm = 10 log10 [200mW/1mW]
= 10(200)
= 23 dBm

21/06/15 45
Limitation in a Communication System
There are two categories of limitations:
 Technological constraint
 Equipment ability
 Economy and cost factor
 National and international law and agreement as well as
standardization (such as ITU etc)
 Interaction with existing system
 Physical constraint
 Bandwidth
 The difference between the upper frequency and lower
frequency of the signal or the equipment operation range
 Noise
 Any unwanted electrical energy present in the usable passband
of a communication circuit

21/06/15 46
Communication System Chart
Communication
System
Continuous Wave Digital Wave
Amplitude
Modulation
(AM)
Pulse
Modulation
(PM)
Angle
Modulation
Frequency
Modulation
(FM)
Analogue Pulse
Modulation
Digital Pulse
Modulation

1 . introduction to communication system

Recommended

More Related Content

What's hot (20)

Similar to 1 . introduction to communication system (20)

Recently uploaded (20)

1 . introduction to communication system